# generated by SuperSlicer 2.3.57 on 2021-12-31 at 12:57:30 UTC bed_temperature = 100 bridge_fan_speed = 55 bridge_internal_fan_speed = -1 chamber_temperature = 0 compatible_printers = compatible_printers_condition = compatible_prints = compatible_prints_condition = cooling = 1 disable_fan_first_layers = 2 end_filament_gcode = "; Filament-specific end gcode EsunABS+" external_perimeter_fan_speed = -1 extrusion_multiplier = 0.94 fan_always_on = 1 fan_below_layer_time = 10 filament_colour = #424242 filament_cooling_final_speed = 50 filament_cooling_initial_speed = 10 filament_cooling_moves = 5 filament_cooling_zone_pause = 0 filament_cost = 20 filament_custom_variables = "" filament_density = 1.05 filament_deretract_speed = nil filament_diameter = 1.75 filament_dip_extraction_speed = 70 filament_dip_insertion_speed = 33 filament_enable_toolchange_part_fan = 0 filament_enable_toolchange_temp = 0 filament_load_time = 30 filament_loading_speed = 14 filament_loading_speed_start = 19 filament_max_overlap = 100% filament_max_speed = 0 filament_max_volumetric_speed = 25 filament_max_wipe_tower_speed = 200 filament_melt_zone_pause = 0 filament_minimal_purge_on_wipe_tower = 150 filament_notes = "" filament_ramming_parameters = "120 110 5.56452 5.6129 5.69355 5.93548 6.5 7.29032 8.06452 8.72581 9.30645 9.79032 10.1129 10.2581| 0.05 5.56775 0.45 5.63874 0.95 6.05808 1.45 7.59034 1.95 8.95803 2.45 9.93557 2.95 10.3096 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_speed = nil filament_seam_gap = nil filament_settings_id = EsunABS+ filament_shrink = 100% filament_skinnydip_distance = 42 filament_soluble = 0 filament_spool_weight = 1000 filament_toolchange_delay = 0 filament_toolchange_part_fan_speed = 50 filament_toolchange_temp = 240 filament_type = ABS filament_unload_time = 30 filament_unloading_speed = 20 filament_unloading_speed_start = 100 filament_use_fast_skinnydip = 0 filament_use_skinnydip = 1 filament_vendor = Esun filament_wipe = nil filament_wipe_advanced_pigment = 0.4 filament_wipe_extra_perimeter = nil filament_wipe_only_crossing = nil filament_wipe_speed = nil first_layer_bed_temperature = 105 first_layer_temperature = 250 full_fan_speed_layer = 0 inherits = max_fan_speed = 50 max_speed_reduction = 90% min_fan_speed = 30 min_print_speed = 15 slowdown_below_layer_time = 20 start_filament_gcode = "; Filament-specific start gcode EsunABS+\nM107 S{min_fan_speed}" temperature = 250 top_fan_speed = -1