diff --git a/printer.cfg b/printer.cfg index 489a37c..d661a38 100644 --- a/printer.cfg +++ b/printer.cfg @@ -40,6 +40,7 @@ max_z_velocity: 25 #Max 15 for 12V TMC Drivers, can increase for 24V max_z_accel: 350 square_corner_velocity: 5.0 + ##################################################################### # X/Y Stepper Settings ##################################################################### @@ -54,26 +55,12 @@ microsteps: 16 full_steps_per_rotation: 400 # 200: 1.8 deg stepper, 400: 0.9 deg stepper endstop_pin: PG6 position_min: 0 -##-------------------------------------------------------------------- - -## Uncomment below for 250mm build -#position_endstop: 250 -#position_max: 250 - -## Uncomment for 300mm build position_endstop: 300 position_max: 300 - -## Uncomment for 350mm build -#position_endstop: 350 -#position_max: 350 - -##-------------------------------------------------------------------- homing_speed: 25 #Max 100 homing_retract_dist: 5 homing_positive_dir: true -## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_x] uart_pin: PC4 interpolate: True @@ -92,26 +79,12 @@ microsteps: 16 full_steps_per_rotation: 400 # 200: 1.8 deg stepper, 400: 0.9 deg stepper endstop_pin: PG9 position_min: 0 -##-------------------------------------------------------------------- - -## Uncomment for 250mm build -#position_endstop: 250 -#position_max: 250 - -## Uncomment for 300mm build position_endstop: 305 position_max: 305 - -## Uncomment for 350mm build -#position_endstop: 350 -#position_max: 350 - -##-------------------------------------------------------------------- homing_speed: 25 #Max 100 homing_retract_dist: 5 homing_positive_dir: true -## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_y] uart_pin: PD11 interpolate: True @@ -120,6 +93,7 @@ hold_current: 0.7 sense_resistor: 0.110 stealthchop_threshold: 0 + ##################################################################### # Z Stepper Settings ##################################################################### @@ -127,7 +101,6 @@ stealthchop_threshold: 0 ## Z0 Stepper - Front Left on MOTOR2_1 [stepper_z] step_pin: PF11 -# dir_pin: !PG3 dir_pin: PG3 enable_pin: !PG5 rotation_distance: 40 @@ -139,24 +112,12 @@ endstop_pin: PG10 ## Increasing position_endstop brings nozzle closer to the bed ## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config position_endstop: -0.5 -##-------------------------------------------------------------------- - -## Uncomment below for 250mm build -#position_max: 240 - -## Uncomment below for 300mm build position_max: 290 - -## Uncomment below for 350mm build -#position_max: 340 - -##-------------------------------------------------------------------- position_min: -5 homing_speed: 8 second_homing_speed: 3 homing_retract_dist: 3 -## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z] uart_pin: PC6 interpolate: true @@ -168,14 +129,12 @@ stealthchop_threshold: 0 ## Z1 Stepper - Rear Left on MOTOR3 [stepper_z1] step_pin: PG4 -# dir_pin: PC1 dir_pin: !PC1 enable_pin: !PA0 rotation_distance: 40 gear_ratio: 80:16 microsteps: 16 -## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z1] uart_pin: PC7 interpolate: true @@ -187,14 +146,12 @@ stealthchop_threshold: 0 ## Z2 Stepper - Rear Right on MOTOR4 [stepper_z2] step_pin: PF9 -# dir_pin: !PF10 dir_pin: PF10 enable_pin: !PG2 rotation_distance: 40 gear_ratio: 80:16 microsteps: 16 -## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z2] uart_pin: PF2 interpolate: true @@ -206,14 +163,12 @@ stealthchop_threshold: 0 ## Z3 Stepper - Front Right on MOTOR5 [stepper_z3] step_pin: PC13 -# dir_pin: PF0 dir_pin: !PF0 enable_pin: !PF1 rotation_distance: 40 gear_ratio: 80:16 microsteps: 16 -## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z3] uart_pin: PE4 interpolate: true @@ -263,7 +218,6 @@ pressure_advance: 0.05 pressure_advance_smooth_time: 0.040 ## E0 on MOTOR6 -## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 extruder] uart_pin: PE1 interpolate: false @@ -291,6 +245,7 @@ max_temp: 120 #pid_ki: 2.347 #pid_kd: 363.769 + ##################################################################### # Probe ##################################################################### @@ -309,6 +264,7 @@ sample_retract_dist: 3.0 samples_tolerance: 0.006 samples_tolerance_retries: 3 + ##################################################################### # Fan Control ##################################################################### @@ -349,6 +305,7 @@ heater_temp: 45.0 #heater_temp: 60 #fan_speed: 1.0 + ##################################################################### # LED Control ##################################################################### @@ -361,10 +318,12 @@ heater_temp: 45.0 #value:1 #cycle_time: 0.01 + ##################################################################### # Homing and Gantry Adjustment Routines ##################################################################### + ##################################################################### # Enclosure Temp Sensor Section ##################################################################### @@ -386,63 +345,27 @@ timeout: 1800 [safe_z_home] ## XY Location of the Z Endstop Switch -## Update -10,-10 to the XY coordinates of your endstop pin -## (such as 157,305) after going through Z Endstop Pin -## Location Definition step. home_xy_position: 208, 305 speed:100 z_hop:10 [quad_gantry_level] ## Use QUAD_GANTRY_LEVEL to level a gantry. -## Min & Max gantry corners - measure from nozzle at MIN (0,0) and -## MAX (250, 250), (300,300), or (350,350) depending on your printer size -## to respective belt positions - -#-------------------------------------------------------------------- -## Gantry Corners for 250mm Build -## Uncomment for 250mm build -#gantry_corners: -# -60,-10 -# 310, 320 -## Probe points -#points: -# 50,25 -# 50,175 -# 200,175 -# 200,25 - -## Gantry Corners for 300mm Build -## Uncomment for 300mm build gantry_corners: -60,-10 360,370 -# Probe points points: 50,25 50,225 250,225 250,25 - -## Gantry Corners for 350mm Build -## Uncomment for 350mm build -#gantry_corners: -# -60,-10 -# 410,420 -## Probe points -#points: -# 50,25 -# 50,275 -# 300,275 -# 300,25 - -#-------------------------------------------------------------------- speed: 100 horizontal_move_z: 10 retries: 5 retry_tolerance: 0.0075 max_adjust: 10 + ######################################## # EXP1 / EXP2 (display) pins ######################################## @@ -463,28 +386,11 @@ aliases: EXP2_7=PC15, EXP2_8=, EXP2_9=, EXP2_10=<5V> + ##################################################################### # Displays ##################################################################### -## Uncomment the display that you have -#-------------------------------------------------------------------- - -#[display] -## RepRapDiscount 128x64 Full Graphic Smart Controller -#lcd_type: st7920 -#cs_pin: EXP1_4 -#sclk_pin: EXP1_5 -#sid_pin: EXP1_3 -#menu_timeout: 40 -#encoder_pins: ^EXP2_5, ^EXP2_3 -#click_pin: ^!EXP1_2 - -#[output_pin beeper] -#pin: EXP1_1 - -#-------------------------------------------------------------------- - [display] # mini12864 LCD Display lcd_type: uc1701 @@ -516,8 +422,6 @@ gcode: SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 -#-------------------------------------------------------------------- - ##################################################################### # Macros @@ -529,18 +433,9 @@ gcode: G28 QUAD_GANTRY_LEVEL G28 - ## Uncomment for for your size printer: - #-------------------------------------------------------------------- - ## Uncomment for 250mm build - #G0 X125 Y125 Z30 F3600 - - ## Uncomment for 300 build G0 X150 Y150 Z30 F3600 - - ## Uncomment for 350mm build - #G0 X175 Y175 Z30 F3600 - #-------------------------------------------------------------------- + [gcode_macro PRINT_START] # Use PRINT_START for the slicer starting script - please customise for your slicer of choice gcode: @@ -562,15 +457,7 @@ gcode: G90 ; absolute positioning G0 X125 Y250 F3600 ; park nozzle at rear BED_MESH_CLEAR - -## Thermistor Types -## "EPCOS 100K B57560G104F" -## "ATC Semitec 104GT-2" -## "NTC 100K beta 3950" -## "Honeywell 100K 135-104LAG-J01" -## "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad) -## "AD595" -## "PT100 INA826" + #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.