diff --git a/display.cfg b/display.cfg
deleted file mode 100644
index 5f80b7e..0000000
--- a/display.cfg
+++ /dev/null
@@ -1,286 +0,0 @@
-#####################################################################
-#  Displays
-#####################################################################
-
-[board_pins]
-aliases:
-  # EXP1 header
-  EXP1_1=PE8, EXP1_2=PE7,
-  EXP1_3=PE9, EXP1_4=PE10,
-  EXP1_5=PE12, EXP1_6=PE13,    # Slot in the socket on this side
-  EXP1_7=PE14, EXP1_8=PE15,
-  EXP1_9=<GND>, EXP1_10=<5V>,
-
-  # EXP2 header
-  EXP2_1=PA6, EXP2_2=PA5,
-  EXP2_3=PB1, EXP2_4=PA4,
-  EXP2_5=PB2, EXP2_6=PA7,      # Slot in the socket on this side
-  EXP2_7=PC15, EXP2_8=<RST>,
-  EXP2_9=<GND>, EXP2_10=<5V>
-
-[display]
-# mini12864 LCD Display
-lcd_type: uc1701
-cs_pin: EXP1_3
-a0_pin: EXP1_4
-rst_pin: EXP1_5
-encoder_pins: ^EXP2_5, ^EXP2_3
-click_pin: ^!EXP1_2
-contrast: 63
-spi_software_miso_pin: EXP2_1
-spi_software_mosi_pin: EXP2_6
-spi_software_sclk_pin: EXP2_2
-# display_group: __voron_display
-
-[neopixel btt_mini12864]
-# To control Neopixel RGB in mini12864 display
-pin: EXP1_6
-chain_count: 3
-initial_RED: 0.1
-initial_GREEN: 0.5
-initial_BLUE: 0.0
-color_order: RGB
-
-# Set RGB values on boot up for each Neopixel.
-# Index 1 = display, Index 2 and 3 = Knob
-[delayed_gcode setdisplayneopixel]
-initial_duration: 1
-gcode:
-  SET_LED LED=btt_mini12864 RED=0.50 GREEN=0.00 BLUE=0.00 INDEX=1 TRANSMIT=0
-  SET_LED LED=btt_mini12864 RED=0.13 GREEN=0.16 BLUE=1.00 INDEX=2 TRANSMIT=0
-  SET_LED LED=btt_mini12864 RED=0.13 GREEN=0.16 BLUE=1.00 INDEX=3
-
-
-#####################################################################
-# Display Menu definition
-#####################################################################
-
-# Removed items
-[menu __main __octoprint]
-type: disabled
-
-## Control
-[menu __main __control __home]
-type: disabled
-
-[menu __main __control __homez]
-type: disabled
-
-[menu __main __control __homexy]
-type: disabled
-
-##  PreHeat
-[menu __main __temp __preheat_pla]
-type: disabled
-
-[menu __main __temp __preheat_abs]
-type: disabled
-
-##  use own load and unload macro
-[menu __main __filament __loadf]
-type: disabled
-
-[menu __main __filament __loads]
-type: disabled
-
-[menu __main __filament __unloadf]
-type: disabled
-
-[menu __main __filament __unloads]
-type: disabled
-
-## Control
-[menu __main __control __home]
-type: disabled
-
-[menu __main __control __homez]
-type: disabled
-
-[menu __main __control __homexy]
-type: disabled
-
-
-# Bed Probe
-[menu __main __setup __calib __bedprobe]
-type: disabled
-
-##  Delta Calibration
-[menu __main __setup __calib __delta_calib_auto]
-type: disabled
-
-[menu __main __setup __calib __delta_calib_man]
-type: disabled
-
-
-# Added Items to the Stock menu
-## Control
-[menu __main __control __home]
-type: input
-enable: {not printer.idle_timeout.state == "Printing"}
-name: Home: {['noop', 'ALL', 'XY', 'Z'][menu.input|int]}
-input: 0
-input_min: 0
-input_max: 3
-input_step: 1
-gcode:
-  {%- if menu.event == 'long_click' -%}
-    {[' ', 'G28', 'G28 XY', 'G28 Z'][menu.input|int]}
-  {%- endif -%}
-
-[menu __main __control __move]
-type: input
-enable: {not printer.idle_timeout.state == "Printing"}
-name: Move: {['FRONT CENTER', 'CENTER', 'REAR CENTER'][menu.input|int]}
-input: 0
-input_min: 0
-input_max: 2
-input_step: 1
-gcode:
-  {%- if menu.event == 'long_click' -%}
-    CENTER {['Y=15', '', 'Y=290'][menu.input|int]}
-  {%- endif -%}
-
-
-## Filament
-[menu __main __filament __preheat]
-type: input
-enable: {not printer.idle_timeout.state == "Printing"}
-name: Preheat: {['Off', 'ABS', 'PLA', 'PET'][menu.input|int]}
-input: 0
-input_min: 0
-input_max: 3
-input_step: 1
-gcode:
-  {%- if menu.event == 'long_click' -%}
-    M104 S{[0, 215, 190, 200][menu.input|int]}
-  {%- endif -%}
-
-
-[menu __main __filament __filament_load]
-type: input
-enable: {not printer.idle_timeout.state == "Printing"}
-name: Filament: {['noop', 'Load', 'Unload', 'Purge (10mm)'][menu.input|int]}
-input: 0
-input_min: 0
-input_max: 3
-input_step: 1
-gcode:
-  {%- if menu.event == 'long_click' -%}
-    {% if printer.extruder.can_extrude|lower == 'true' %}
-      M83
-      G1 {['E0', 'E50 F3000', 'E-75 F3000', 'E10 F300'][menu.input|int]}
-      G1 {['E0', 'E35 F300', 'E0', 'E0'][menu.input|int]}
-      M82
-    {% else %}
-      {action_respond_info("extruder not hot enough")}
-    {%- endif -%}
-  {%- endif -%}
-
-
-## Calibration
-[menu __main __setup __calib __bedprobe]
-type: command
-enable: {not printer.idle_timeout.state == "Printing"}
-name: Bed probe
-gcode:
-  {%- if printer.toolhead.position.y|float < 270 -%}
-    PROBE
-  {%- else -%}
-    {action_respond_info("Won't probe inunsafe position")}
-  {%- endif -%}
-
-
-## Probe & Endstop Z-Offset calibration
-[menu __main __setup __calib __Z_offset]
-type: list
-enable: {not printer.idle_timeout.state == "Printing"}
-name: Z offset
-
-[menu __main __setup __calib __Z_offset __start]
-type: input
-enable: {not printer.idle_timeout.state == "Printing"}
-name: Calibrate: {['noop','Probe','Endstop'][menu.input|int]}
-input: 0
-input_min: 0
-input_max: 2
-input_step: 1
-gcode:
-  {%- if menu.event == 'long_click' -%}
-    {menu.back()}
-  {%- endif -%}
-  {%- if menu.input|int == 1 -%}
-    {% if "xyz" in printer.toolhead.homed_axes %}
-      {action_respond_info("Start Probe calibration")}
-      CENTER
-      PROBE_CALIBRATE
-    {%- else -%}
-      {action_respond_info("Printer not homed")}
-    {%- endif -%}
-  {%- elif menu.input|int == 2 -%}
-    {% if "xyz" in printer.toolhead.homed_axes %}
-      {action_respond_info(" Start Z-Endstop calibration")}
-      CENTER
-      Z_ENDSTOP_CALIBRATE
-    {%- else -%}
-      {action_respond_info("Printer not homed")}
-    {%- endif -%}
-  {%- endif -%}
-
-
-[menu __main __setup __calib __Z_offset __move_z]
-type: input
-name: Move Z: {'%03.2f' % menu.input}
-input: {printer.gcode_move.gcode_position.z}
-input_step: 1
-realtime: True
-gcode:
-  {%- if menu.event == 'change' -%}
-    G1 Z{'%.2f' % menu.input}
-  {%- elif menu.event == 'long_click' -%}
-    G1 Z{'%.2f' % menu.input}
-    SAVE_GCODE_STATE NAME=__move__axis
-    G91
-    G1 Z2
-    G1 Z-2
-    RESTORE_GCODE_STATE NAME=__move__axis
-  {%- endif -%}
-
-[menu __main __setup __calib __Z_offset __test_z]
-type: input
-name: Test Z: {['-1.0', '-0.5', '-0.1', '-.05', '-.01', '0.0', '+0.01', '+0.05', '+0.1', '+0.5', '+1.0'][menu.input|int]}
-input: 5
-input_min: 0
-input_max: 10
-input_step: 1
-gcode:
-  {%- if menu.event == 'long_click' -%}
-    TESTZ Z={['-1.0', '-0.5', '-0.1', '-.05', '-.01', '0', '+0.01', '+0.05', '+0.1', '+0.5', '+1.0'][menu.input|int]}
-  {%- endif -%}
-
-[menu __main __setup __calib __Z_offset __test_z_live]
-type: input
-name: Test Z : {'%03.3f' % menu.input}
-input: 0
-input_min: -5.0
-input_max: 5.0
-input_step: 0.01
-realtime: True
-gcode:
-  {%- if menu.event == 'long_click' -%}
-    TESTZ Z={'%.3f' % menu.input}
-  {%- endif -%}
-
-[menu __main __setup __calib __Z_offset __accept]
-type: command
-name: Accept
-gcode: ACCEPT
-
-[menu __main __setup __calib __Z_offset __abort]
-type: command
-name: Abort
-gcode: ABORT
-
-[menu __main __setup __calib __Z_offset __saveconfig]
-type: command
-name: Save config
-gcode: SAVE_CONFIG