diff --git a/printer.cfg b/printer.cfg index 3fd32a2..8d9650d 100644 --- a/printer.cfg +++ b/printer.cfg @@ -10,21 +10,21 @@ ## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config ## *** THINGS TO CHANGE/CHECK: *** -## MCU paths [mcu] section -## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file -## Z Endstop Switch location [safe_z_home] section -## Homing end position [gcode_macro G32] section -## Z Endstop Switch offset for Z0 [stepper_z] section -## Probe points [quad_gantry_level] section -## Min & Max gantry corner postions [quad_gantry_level] section -## PID tune [extruder] and [heater_bed] sections -## Fine tune E steps [extruder] section +## MCU paths [mcu] section +## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file +## Z Endstop Switch location [safe_z_home] section +## Homing end position [gcode_macro G32] section +## Z Endstop Switch offset for Z0 [stepper_z] section +## Probe points [quad_gantry_level] section +## Min & Max gantry corner postions [quad_gantry_level] section +## PID tune [extruder] and [heater_bed] sections +## Fine tune E steps [extruder] section [mcu] -## [X in MOTOR0] - B Motor -## [Y in MOTOR1] - A Motor -## [E in MOTOR6] - Extruder -## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +## [X in MOTOR0] - B Motor +## [Y in MOTOR1] - A Motor +## [E in MOTOR6] - Extruder +## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_1E0030000E5053424E363620-if00 #restart_method: command @@ -32,29 +32,30 @@ serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_1E0030000E5053424E363620-if00 [printer] kinematics: corexy -max_velocity: 300 -max_accel: 3000 #Max 4000 -max_z_velocity: 25 #Max 15 for 12V TMC Drivers, can increase for 24V +max_velocity: 300 +max_accel: 3000 # Max 4000 +max_accel_to_decel: 1500 # default half of max_accel +max_z_velocity: 25 # Max 15 for 12V TMC Drivers, can increase for 24V max_z_accel: 350 square_corner_velocity: 5.0 ##################################################################### -# fluidd +# fluidd ##################################################################### [include fluidd.cfg] ##################################################################### -# Macros +# Macros ##################################################################### [include macros.cfg] ##################################################################### -# X/Y Stepper Settings +# X/Y Stepper Settings ##################################################################### ## X Stepper on MOTOR0(B Motor) @@ -64,12 +65,12 @@ dir_pin: !PF12 enable_pin: !PF14 rotation_distance: 40 microsteps: 16 -full_steps_per_rotation: 400 # 200: 1.8 deg stepper, 400: 0.9 deg stepper +full_steps_per_rotation: 400 # 1.8 deg stepper: 200, 0.9 deg stepper endstop_pin: PG6 position_min: 0 position_endstop: 300 position_max: 300 -homing_speed: 25 #Max 100 +homing_speed: 25 # Max 100 homing_retract_dist: 5 homing_positive_dir: true @@ -104,10 +105,10 @@ run_current: 0.8 hold_current: 0.7 sense_resistor: 0.110 stealthchop_threshold: 0 - + ##################################################################### -# Z Stepper Settings +# Z Stepper Settings ##################################################################### ## Z0 Stepper - Front Left on MOTOR2_1 @@ -119,10 +120,10 @@ rotation_distance: 40 gear_ratio: 80:16 microsteps: 16 endstop_pin: PG10 -## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) -## (+) value = endstop above Z0, (-) value = endstop below -## Increasing position_endstop brings nozzle closer to the bed -## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config +## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) +## (+) value = endstop above Z0, (-) value = endstop below +## Increasing position_endstop brings nozzle closer to the bed +## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config #position_endstop: -0.5 position_max: 290 position_min: -5 @@ -138,7 +139,7 @@ hold_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 -## Z1 Stepper - Rear Left on MOTOR3 +## Z1 Stepper - Rear Left on MOTOR3 [stepper_z1] step_pin: PG4 dir_pin: !PC1 @@ -155,7 +156,7 @@ hold_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 -## Z2 Stepper - Rear Right on MOTOR4 +## Z2 Stepper - Rear Right on MOTOR4 [stepper_z2] step_pin: PF9 dir_pin: PF10 @@ -172,7 +173,7 @@ hold_current: 0.80 sense_resistor: 0.110 stealthchop_threshold: 0 -## Z3 Stepper - Front Right on MOTOR5 +## Z3 Stepper - Front Right on MOTOR5 [stepper_z3] step_pin: PC13 dir_pin: !PF0 @@ -191,29 +192,29 @@ stealthchop_threshold: 0 ##################################################################### -# Extruder +# Extruder ##################################################################### -# E0 on MOTOR6 +# E0 on MOTOR6 [extruder] step_pin: PE2 dir_pin: !PE3 enable_pin: !PD4 -## Update value below when you perform extruder calibration -## If you ask for 100mm of filament, but in reality it is 98mm: -## rotation_distance = * / 100 -## 22.6789511 is a good starting point -rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears -## Update Gear Ratio depending on your Extruder Type -## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio) -## Use 80:20 for M4, M3.1 -gear_ratio: 50:17 #BMG Gear Ratio +## Update value below when you perform extruder calibration +## If you ask for 100mm of filament, but in reality it is 98mm: +## rotation_distance = * / 100 +## 22.6789511 is a good starting point +rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears +## Update Gear Ratio depending on your Extruder Type +## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio) +## Use 80:20 for M4, M3.1 +gear_ratio: 50:17 # BMG Gear Ratio microsteps: 16 -full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree +full_steps_per_rotation: 200 # 1.8 deg stepper: 200, 0.9 deg stepper nozzle_diameter: 0.400 filament_diameter: 1.75 heater_pin: PA2 -## Validate the following thermistor type to make sure it is correct +## Validate the following thermistor type to make sure it is correct sensor_type: ATC Semitec 104GT-2 sensor_pin: PF4 min_temp: 10 @@ -224,12 +225,12 @@ min_extrude_temp: 170 #pid_kp = 26.213 #pid_ki = 1.304 #pid_kd = 131.721 -## Try to keep pressure_advance below 1.0 +## Try to keep pressure_advance below 1.0 pressure_advance: 0.05 -## Default is 0.040, leave stock +## Default is 0.040, leave stock pressure_advance_smooth_time: 0.040 -## E0 on MOTOR6 +## E0 on MOTOR6 [tmc2209 extruder] uart_pin: PE1 interpolate: false @@ -240,16 +241,16 @@ stealthchop_threshold: 0 ##################################################################### -# Bed Heater +# Bed Heater ##################################################################### [heater_bed] -## SSR Pin - BED_OUT +## SSR Pin - BED_OUT heater_pin: PA1 sensor_type: NTC 100K beta 3950 sensor_pin: PF3 -## Adjust Max Power so your heater doesn't warp your bed -max_power: 0.8 # 0.4W per cm2, 360W for 300 build +## Adjust Max Power so your heater doesn't warp your bed +max_power: 0.8 # 0.4W per cm2, 360W for 300 build min_temp: 0 max_temp: 120 #control: pid @@ -259,12 +260,12 @@ max_temp: 120 ##################################################################### -# Probe +# Probe ##################################################################### [probe] -## Inductive Probe -## This probe is not used for Z height, only Quad Gantry Leveling +## Inductive Probe +## This probe is not used for Z height, only Quad Gantry Leveling pin: ~PB7 x_offset: 0 y_offset: 25.0 @@ -278,37 +279,37 @@ samples_tolerance_retries: 3 ##################################################################### -# Fan Control +# Fan Control ##################################################################### [fan] -## Print Cooling Fan - CNC_FAN0 +## Print Cooling Fan - CNC_FAN0 pin: PA8 kick_start_time: 0.5 -## Depending on your fan, you may need to increase this value -## if your fan will not start. Can change cycle_time (increase) -## if your fan is not able to slow down effectively +## Depending on your fan, you may need to increase this value +## if your fan will not start. Can change cycle_time (increase) +## if your fan is not able to slow down effectively off_below: 0.10 [heater_fan hotend_fan] -## Hotend Fan - CNC_FAN1 +## Hotend Fan - CNC_FAN1 pin: PE5 max_power: 1.0 kick_start_time: 0.5 heater: extruder heater_temp: 50.0 -## If you are experiencing back flow, you can reduce fan_speed +## If you are experiencing back flow, you can reduce fan_speed #fan_speed: 1.0 [heater_fan controller_fan] -## Controller fan - CNC_FAN2 +## Controller fan - CNC_FAN2 pin: PD12 kick_start_time: 0.5 heater: heater_bed heater_temp: 45.0 #[heater_fan exhaust_fan] -## Exhaust fan - CNC_FAN3 +## Exhaust fan - CNC_FAN3 #pin: PD13 #max_power: 1.0 #shutdown_speed: 0.0 @@ -319,7 +320,7 @@ heater_temp: 45.0 ##################################################################### -# LED Control +# LED Control ##################################################################### #[output_pin caselight] @@ -332,12 +333,12 @@ heater_temp: 45.0 ##################################################################### -# Homing and Gantry Adjustment Routines +# Homing and Gantry Adjustment Routines ##################################################################### ##################################################################### -# Enclosure Temp Sensor Section +# Enclosure Temp Sensor Section ##################################################################### [thermistor chamber_temp] temperature1: 25 @@ -356,8 +357,8 @@ gcode_id: C timeout: 1800 [safe_z_home] -## XY Location of the Z Endstop Switch -home_xy_position: 208, 305 +## XY Location of the Z Endstop Switch +home_xy_position: 208, 305 speed:100 z_hop:10 @@ -373,15 +374,15 @@ algorithm: bicubic relative_reference_index: 12 [quad_gantry_level] -## Use QUAD_GANTRY_LEVEL to level a gantry. +## Use QUAD_GANTRY_LEVEL to level a gantry. gantry_corners: - -60,-10 - 360,370 + -60,-10 + 360,370 points: - 50,25 - 50,225 - 250,225 - 250,25 + 50,25 + 50,225 + 250,225 + 250,25 speed: 100 horizontal_move_z: 10 retries: 5 @@ -395,27 +396,27 @@ max_adjust: 10 [board_pins] aliases: - # EXP1 header - EXP1_1=PE8, EXP1_2=PE7, - EXP1_3=PE9, EXP1_4=PE10, - EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side - EXP1_7=PE14, EXP1_8=PE15, - EXP1_9=, EXP1_10=<5V>, + # EXP1 header + EXP1_1=PE8, EXP1_2=PE7, + EXP1_3=PE9, EXP1_4=PE10, + EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side + EXP1_7=PE14, EXP1_8=PE15, + EXP1_9=, EXP1_10=<5V>, - # EXP2 header - EXP2_1=PA6, EXP2_2=PA5, - EXP2_3=PB1, EXP2_4=PA4, - EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side - EXP2_7=PC15, EXP2_8=, - EXP2_9=, EXP2_10=<5V> + # EXP2 header + EXP2_1=PA6, EXP2_2=PA5, + EXP2_3=PB1, EXP2_4=PA4, + EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side + EXP2_7=PC15, EXP2_8=, + EXP2_9=, EXP2_10=<5V> ##################################################################### -# Displays +# Displays ##################################################################### [display] -# mini12864 LCD Display +# mini12864 LCD Display lcd_type: uc1701 cs_pin: EXP1_3 a0_pin: EXP1_4 @@ -428,7 +429,7 @@ spi_software_mosi_pin: EXP2_6 spi_software_sclk_pin: EXP2_2 [neopixel btt_mini12864] -# To control Neopixel RGB in mini12864 display +# To control Neopixel RGB in mini12864 display pin: EXP1_6 chain_count: 3 initial_RED: 0.1 @@ -436,15 +437,14 @@ initial_GREEN: 0.5 initial_BLUE: 0.0 color_order: RGB -# Set RGB values on boot up for each Neopixel. -# Index 1 = display, Index 2 and 3 = Knob +# Set RGB values on boot up for each Neopixel. +# Index 1 = display, Index 2 and 3 = Knob [delayed_gcode setdisplayneopixel] initial_duration: 1 gcode: - SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 - SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 - SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 - + SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 + SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 + SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. @@ -464,21 +464,21 @@ gcode: #*# [bed_mesh default] #*# version = 1 #*# points = -#*# 0.382500, 0.377500, 0.370000, 0.357500, 0.337500 -#*# 0.340000, 0.330000, 0.305000, 0.305000, 0.295000 -#*# 0.342500, 0.342500, 0.325000, 0.305000, 0.270000 -#*# 0.335000, 0.350000, 0.327500, 0.322500, 0.307500 -#*# 0.382500, 0.407500, 0.392500, 0.382500, 0.355000 +#*# 0.085000, 0.102500, 0.075000, 0.080000, 0.060000 +#*# 0.057500, 0.062500, 0.020000, 0.032500, 0.035000 +#*# 0.027500, 0.035000, 0.000000, 0.000000, -0.007500 +#*# 0.020000, 0.032500, -0.005000, 0.017500, 0.020000 +#*# 0.072500, 0.085000, 0.045000, 0.057500, 0.057500 #*# tension = 0.2 -#*# min_x = 25.0 +#*# min_x = 40.0 #*# algo = bicubic #*# y_count = 5 #*# mesh_y_pps = 2 -#*# min_y = 25.0 +#*# min_y = 40.0 #*# x_count = 5 -#*# max_y = 287.0 +#*# max_y = 260.0 #*# mesh_x_pps = 2 -#*# max_x = 261.0 +#*# max_x = 260.0 #*# #*# [stepper_z] -#*# position_endstop = 0.542 +#*# position_endstop = 0.642