initial commit
This commit is contained in:
commit
633b62d3f5
2 changed files with 440 additions and 0 deletions
35
moonraker.conf
Normal file
35
moonraker.conf
Normal file
|
|
@ -0,0 +1,35 @@
|
|||
[server]
|
||||
host: 0.0.0.0
|
||||
port: 7125
|
||||
enable_debug_logging: False
|
||||
config_path: ~/klipper_config
|
||||
|
||||
[authorization]
|
||||
enabled: True
|
||||
cors_domains:
|
||||
https://my.mainsail.xyz
|
||||
http://my.mainsail.xyz
|
||||
http://*.local
|
||||
http://*.lan
|
||||
trusted_clients:
|
||||
10.0.0.0/8
|
||||
127.0.0.0/8
|
||||
169.254.0.0/16
|
||||
172.16.0.0/12
|
||||
192.168.0.0/16
|
||||
FE80::/10
|
||||
::1/128
|
||||
|
||||
# enables partial support of Octoprint API
|
||||
[octoprint_compat]
|
||||
|
||||
# enables moonraker to track and store print history.
|
||||
[history]
|
||||
|
||||
# this enables moonraker's update manager
|
||||
[update_manager]
|
||||
|
||||
[update_manager client mainsail]
|
||||
type: web
|
||||
repo: meteyou/mainsail
|
||||
path: ~/mainsail
|
||||
405
printer.cfg
Normal file
405
printer.cfg
Normal file
|
|
@ -0,0 +1,405 @@
|
|||
# This file contains common configurations and pin mappings for the Prusa
|
||||
# Mini+, which uses the Prusa Buddy board.
|
||||
|
||||
# To use this config, the firmware should be compiled for the STM32F407. When
|
||||
# running "make menuconfig", enable "extra low-level configuration setup",
|
||||
# select the "128KiB + 512 byte offset" bootloader, and USB communication.
|
||||
# Connect the printer to your Raspberry Pi using the printer's micro-USB port.
|
||||
# If you prefer to remove Prusa's stock bootloader entirely, select the
|
||||
# "No bootloader" option.
|
||||
|
||||
# When flashing for the first time, you will need to break the "appendix"
|
||||
# on the Buddy board, then put the device into DFU mode by moving the jumper
|
||||
# on the 3-pin header (older boards) or shorting the 2-pin header (newer boards)
|
||||
# and resetting, and finally use "make flash" to install Klipper. Once Klipper is
|
||||
# installed, you no longer need the jumper - just use "make flash" which will
|
||||
# automatically put the device into DFU mode.
|
||||
|
||||
# Note that if you were previously running Prusa firmware, you must fully
|
||||
# power cycle the board after flashing. Otherwise, Klipper will be unable to
|
||||
# communicate with the TMC2209s due to the abrupt change in the baud rate,
|
||||
# and will show this error: "Unable to read tmc uart register IFCNT".
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[pause_resume]
|
||||
|
||||
[display_status]
|
||||
|
||||
[virtual_sdcard]
|
||||
path: ~/gcode_files
|
||||
|
||||
######################################################################
|
||||
# Macros
|
||||
######################################################################
|
||||
|
||||
# custom slicer START_PRINT and END_PRINT macros
|
||||
[gcode_macro START_PRINT]
|
||||
description: start printing
|
||||
gcode:
|
||||
{% set BED_TEMP = params.BED_TEMP|default(60)|float %}
|
||||
{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(190)|float %}
|
||||
M140 S{BED_TEMP} # Start bed heating
|
||||
M109 S{EXTRUDER_TEMP} # Start extruder heating
|
||||
G90 # Use absolute coordinates
|
||||
SET_GCODE_OFFSET Z=0.0 # Reset the G-Code Z offset (adjust Z offset if needed)
|
||||
G28 # Home the printer
|
||||
G1 Z5 F3000 # Move the nozzle near the bed
|
||||
G1 Z0.15 F300 # Move the nozzle very close to the bed
|
||||
M190 S{BED_TEMP} # Wait for bed to reach temperature
|
||||
M109 S{EXTRUDER_TEMP} # Set and wait for nozzle to reach temperature
|
||||
CLEAN_NOZZLE # clean the nozzle
|
||||
|
||||
[gcode_macro END_PRINT]
|
||||
description: end printing
|
||||
gcode:
|
||||
M140 S0 # Turn off bed
|
||||
M104 S0 # Turn off extruder
|
||||
M106 S0 # Turn off fan
|
||||
G91 # Use relativ coordinates
|
||||
G1 X-2 Y-2 E-3 F300 # Move nozzle away from print while retracting
|
||||
G1 Z10 F3000 # Raise nozzle by 10mm
|
||||
G90 # Use absolute coordinates
|
||||
M84 # Disable steppers
|
||||
|
||||
# [gcode_macro PARK]
|
||||
# description: park the print head
|
||||
# rename_existing: G27
|
||||
# gcode:
|
||||
# {% set x = params.X|default(140) %} #edit to your park position
|
||||
# {% set y = params.Y|default(20) %} #edit to your park position
|
||||
# {% set z = params.Z|default(10)|float %} #edit to your park position
|
||||
# {% set e = params.E|default(1) %} #edit to your retract length
|
||||
|
||||
[gcode_macro PAUSE]
|
||||
description: Pause the actual running print
|
||||
rename_existing: PAUSE_BASE
|
||||
gcode:
|
||||
##### set defaults #####
|
||||
{% set x = params.X|default(140) %} #edit to your park position
|
||||
{% set y = params.Y|default(20) %} #edit to your park position
|
||||
{% set z = params.Z|default(10)|float %} #edit to your park position
|
||||
{% set e = params.E|default(1) %} #edit to your retract length
|
||||
##### calculate save lift position #####
|
||||
{% set max_z = printer.toolhead.axis_maximum.z|float %}
|
||||
{% set act_z = printer.toolhead.position.z|float %}
|
||||
{% set lift_z = z|abs %}
|
||||
{% if act_z < (max_z - lift_z) %}
|
||||
{% set z_safe = lift_z %}
|
||||
{% else %}
|
||||
{% set z_safe = max_z - act_z %}
|
||||
{% endif %}
|
||||
##### end of definitions #####
|
||||
PAUSE_BASE
|
||||
G91
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G1 E-{e} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
{% if "xyz" in printer.toolhead.homed_axes %}
|
||||
G1 Z{z_safe}
|
||||
G90
|
||||
G1 X{x} Y{y} F6000
|
||||
{% else %}
|
||||
{action_respond_info("Printer not homed")}
|
||||
{% endif %}
|
||||
|
||||
[gcode_macro RESUME]
|
||||
description: Resume the actual running print
|
||||
rename_existing: RESUME_BASE
|
||||
gcode:
|
||||
##### set defaults #####
|
||||
{% set e = params.E|default(1) %} #edit to your retract length
|
||||
#### get VELOCITY parameter if specified ####
|
||||
{% if 'VELOCITY' in params|upper %}
|
||||
{% set get_params = ('VELOCITY=' + params.VELOCITY) %}
|
||||
{%else %}
|
||||
{% set get_params = "" %}
|
||||
{% endif %}
|
||||
##### end of definitions #####
|
||||
G91
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G1 E{e} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
RESUME_BASE {get_params}
|
||||
|
||||
[gcode_macro CANCEL_PRINT]
|
||||
description: Cancel the actual running print
|
||||
rename_existing: CANCEL_PRINT_BASE
|
||||
gcode:
|
||||
TURN_OFF_HEATERS
|
||||
CANCEL_PRINT_BASE
|
||||
|
||||
[gcode_macro CLEAN_NOZZLE]]
|
||||
description: clean the nozzle
|
||||
gcode:
|
||||
{% set BED_TEMP = params.BED_TEMP|default(60)|float %}
|
||||
{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(190)|float %}
|
||||
{% set X1 = params.X1|default(120)|float %}
|
||||
{% set X2 = params.X2|default(40)|float %}
|
||||
{% set MANUAL = params.MANUAL|default(0) %}
|
||||
SAVE_GCODE_STATE NAME=clean_nozzle_state
|
||||
{% if MANUAL %}
|
||||
G28 # home
|
||||
M104 S{EXTRUDER_TEMP} # start heating extruder
|
||||
M140 S{BED_TEMP} # start heating bed
|
||||
M109 S{EXTRUDER_TEMP} # wait for extruder to reach temperature
|
||||
M190 S{BED_TEMP} # wait for bed to reach temperature
|
||||
{% endif %}
|
||||
G90 # absolute positioning
|
||||
G92 E0
|
||||
G0 F1500
|
||||
G0 X{X1} Y0 Z5
|
||||
G0 X{X1} Y0 Z0
|
||||
G0 X{X2} Y0 Z0 E10
|
||||
RESTORE_GCODE_STATE NAME=clean_nozzle_state
|
||||
|
||||
[gcode_macro M600]
|
||||
description: Change filament
|
||||
gcode:
|
||||
{% set X = params.X|default(50)|float %}
|
||||
{% set Y = params.Y|default(0)|float %}
|
||||
{% set Z = params.Z|default(10)|float %}
|
||||
SAVE_GCODE_STATE NAME=M600_state
|
||||
PAUSE
|
||||
G91
|
||||
G1 E-.8 F2700
|
||||
G1 Z{Z}
|
||||
G90
|
||||
G1 X{X} Y{Y} F3000
|
||||
G91
|
||||
G1 E-50 F1000
|
||||
RESTORE_GCODE_STATE NAME=M600_state
|
||||
|
||||
## Remove unused gcodes
|
||||
[gcode_macro G29]
|
||||
description: Bed Leveling
|
||||
gcode:
|
||||
G4
|
||||
|
||||
[gcode_macro M201]
|
||||
description: Set Print Max Acceleration
|
||||
gcode:
|
||||
G4
|
||||
|
||||
[gcode_macro M203]
|
||||
description: Set Max Feedrate
|
||||
gcode:
|
||||
G4
|
||||
|
||||
[gcode_macro M205]
|
||||
description: Set Advanced Settings
|
||||
gcode:
|
||||
G4
|
||||
|
||||
[gcode_macro M900]
|
||||
description: Linear Advance Factor
|
||||
gcode:
|
||||
G4
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PD1
|
||||
dir_pin: PD0
|
||||
enable_pin: !PD3
|
||||
microsteps: 16
|
||||
rotation_distance: 32 # 200 * 16 / 100
|
||||
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
||||
position_endstop: 180.4
|
||||
position_min: -2
|
||||
position_max: 180.4
|
||||
homing_speed: 50
|
||||
homing_retract_dist: 0
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PD13
|
||||
dir_pin: PD12
|
||||
enable_pin: !PD14
|
||||
microsteps: 16
|
||||
rotation_distance: 32 # 200 * 16 / 100
|
||||
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
||||
position_endstop: -3
|
||||
position_min: -3
|
||||
position_max: 180
|
||||
homing_speed: 50
|
||||
homing_retract_dist: 0
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PD4
|
||||
dir_pin: !PD15
|
||||
enable_pin: !PD2
|
||||
microsteps: 16
|
||||
rotation_distance: 4
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_min: -3
|
||||
position_max: 185
|
||||
|
||||
[extruder]
|
||||
step_pin: PD9
|
||||
dir_pin: !PD8
|
||||
enable_pin: !PD10
|
||||
microsteps: 16
|
||||
rotation_distance: 26.2564 # (200 * 16 * 48/18) / 325
|
||||
gear_ratio: 48:18
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PB1
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: PC0
|
||||
#control: pid
|
||||
# Prusa's firmware defaults.
|
||||
#pid_Kp: 7
|
||||
#pid_Ki: 0.5
|
||||
#pid_Kd: 45
|
||||
min_temp: 10
|
||||
max_temp: 305
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PD5
|
||||
uart_address: 1
|
||||
diag_pin: ^PE2
|
||||
driver_SGTHRS: 130
|
||||
run_current: 0.35
|
||||
sense_resistor: 0.22
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PD5
|
||||
uart_address: 3
|
||||
diag_pin: ^PE1
|
||||
driver_SGTHRS: 130
|
||||
run_current: 0.35
|
||||
sense_resistor: 0.22
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PD5
|
||||
uart_address: 0
|
||||
diag_pin: ^PE3
|
||||
driver_SGTHRS: 100
|
||||
run_current: 0.35
|
||||
sense_resistor: 0.22
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PD5
|
||||
uart_address: 2
|
||||
diag_pin: ^PA15
|
||||
driver_SGTHRS: 100
|
||||
run_current: 0.4
|
||||
sense_resistor: 0.22
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PB0
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA4
|
||||
#control: pid
|
||||
# Prusa's firmware defaults.
|
||||
#pid_Kp: 120
|
||||
#pid_Ki: 1.5
|
||||
#pid_Kd: 600
|
||||
min_temp: 10
|
||||
max_temp: 110
|
||||
|
||||
# Hotend fan.
|
||||
# The stock firmware uses control ranges of PWM 0-50%, RPM 1000-8000.
|
||||
# Change fan_speed below to match your preference. Measured speeds:
|
||||
# fan_speed 0.5: 50% PWM = 4000RPM (Prusa stock default speed)
|
||||
# fan_speed 1.0: 100% PWM = 8000RPM (safe but loud)
|
||||
[heater_fan hotend_fan]
|
||||
pin: PE9
|
||||
tachometer_pin: PE14
|
||||
fan_speed: 0.5
|
||||
|
||||
# Part cooling fan.
|
||||
# The stock firmware uses control ranges of PWM 10-50%, RPM 500-5000.
|
||||
# To match stock firmware, set the Klipper fan speed to 50%. This speed
|
||||
# can be safely increased to 100% for better part cooling. Measured speeds:
|
||||
# 50% PWM = 2500RPM (Prusa stock default speed)
|
||||
# 100% PWM = 5000RPM (better cooling, still quiet)
|
||||
[fan]
|
||||
pin: PE11
|
||||
tachometer_pin: PE10
|
||||
|
||||
# The SuperPINDA has built-in temperature compensation and no thermistor output,
|
||||
# so no compensation table is needed here.
|
||||
[probe]
|
||||
pin: PA8
|
||||
x_offset: -29
|
||||
y_offset: -3
|
||||
#z_offset: 0 # set this to your Live Z Offset, but negated (invert the sign)
|
||||
speed: 6.0
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 147.4,21.1
|
||||
z_hop: 4
|
||||
|
||||
[bed_mesh]
|
||||
speed: 100
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 10,10
|
||||
mesh_max: 141,167
|
||||
probe_count: 4,4
|
||||
|
||||
[filament_switch_sensor filament_sensor]
|
||||
switch_pin: ^PB4
|
||||
pause_on_runout: True
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_2B0024001547393432343038-if00
|
||||
restart_method: command
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
# Prusa firmware defaults.
|
||||
max_velocity: 180
|
||||
max_accel: 1250
|
||||
max_z_velocity: 12
|
||||
max_z_accel: 400
|
||||
|
||||
[display]
|
||||
lcd_type: st7789v
|
||||
spi_bus: spi2a
|
||||
rst_pin: PC8
|
||||
cs_pin: PC9
|
||||
rs_pin: PD11
|
||||
encoder_pins: ^PE13, ^PE15
|
||||
click_pin: ^!PE12
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 21.307
|
||||
#*# pid_ki = 0.911
|
||||
#*# pid_kd = 124.644
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 57.528
|
||||
#*# pid_ki = 1.059
|
||||
#*# pid_kd = 780.942
|
||||
#*#
|
||||
#*# [probe]
|
||||
#*# z_offset = 1.480
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# -0.058750, -0.003750, 0.102500, 0.057500
|
||||
#*# -0.086250, -0.037500, -0.027500, 0.007500
|
||||
#*# -0.022500, -0.057500, -0.070000, -0.011250
|
||||
#*# -0.066250, -0.102500, -0.045000, -0.071250
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 10.0
|
||||
#*# algo = lagrange
|
||||
#*# y_count = 4
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 4
|
||||
#*# max_y = 166.99
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 140.98
|
||||
Loading…
Reference in a new issue