ercf: switch to Ercf Easy Brd Can

ercf.cfg

@@ -0,0 +1,7 @@
+[include ercf/hardware.cfg]
+[include ercf/software.cfg]
+
+[mcu ercf]
+# serial: /dev/serial/by-id/usb-Klipper_samd21g18a_D3EB9B384134555020312E30171117FF-if00
+canbus_uuid: 092fcd32b788
+

ercf/hardware.cfg

@@ -2,80 +2,74 @@
 
 # This config sample assume you set the two J6 jumpers on 1-2 and 4-5, i.e. [..].[..]
 
-[mcu ercf]
-serial: /dev/serial/by-id/usb-Klipper_samd21g18a_D3EB9B384134555020312E30171117FF-if00
-
 # Carrot Feeder 5mm D-cut shaft
 [manual_stepper gear_stepper]
-step_pin: ercf:PA4
-dir_pin: !ercf:PA10
-enable_pin: !ercf:PA2
+step_pin: ercf:gpio7
+dir_pin: !ercf:gpio8
+enable_pin: !ercf:gpio6
 rotation_distance: 22.6789511 # Bondtech 5mm Drive Gears
 gear_ratio: 80:20
 microsteps: 16
 full_steps_per_rotation: 200
 velocity: 35
 accel: 100
-endstop_pin: ^ercf:PA7
+endstop_pin: ercf:gpio13
 
 [tmc2209 manual_stepper gear_stepper]
 # Adapt accordingly to your setup and desires
 # The default values are tested with the BOM NEMA14 motor
-uart_pin: ercf:PA8          # shared with selector_stepper
-uart_address: 0
+uart_pin: ercf:gpio9
 interpolate: True
 run_current: 0.6
 hold_current: 0.1
 sense_resistor: 0.110
 stealthchop_threshold: 500
-
-[tmc2209 manual_stepper selector_stepper]
-uart_pin: ercf:PA8          # shared with gear_stepper
-uart_address: 1
-run_current: 0.55
-hold_current: 0.4
-interpolate: True
-sense_resistor: 0.110
-stealthchop_threshold: 5000
-# Uncomment the lines below if you want to use sensorless homing for the selector
-#diag_pin: ^P1.27      # Set to MCU pin connected to TMC DIAG pin
-#driver_SGTHRS: 75  # 255 is most sensitive value, 0 is least sensitive
+# diag_pin: ercf:gpio23
 
 [manual_stepper selector_stepper]
-step_pin: ercf:PA9
-dir_pin: !ercf:PB8
-enable_pin: !ercf:PA11
+step_pin: ercf:gpio2
+dir_pin: !ercf:gpio1
+enable_pin: !ercf:gpio3
 microsteps: 16
 rotation_distance: 40
 full_steps_per_rotation: 200
 velocity: 200
 homing_speed: 100
 accel: 600
-endstop_pin: ^ercf:PB9
+# Select the endstop you want depending if you are using sensorless homing
+# endstop_pin: ^ercf:PB9
+endstop_pin: ercf:gpio20
+#endstop_pin: tmc2209_selector_stepper:virtual_endstop
+#endstop_pin: tmc5160_selector_stepper:virtual_endstop
+
+[tmc2209 manual_stepper selector_stepper]
+uart_pin: ercf:gpio0
+run_current: 0.55
+hold_current: 0.4
+interpolate: True
+sense_resistor: 0.110
+stealthchop_threshold: 5000
+# Uncomment the lines below if you want to use sensorless homing for the selector
+# diag_pin: ^ercf:gpio22  # Set to MCU pin connected to TMC DIAG pin
+# driver_SGTHRS: 75       # 255 is most sensitive value, 0 is least sensitive
+
 
 # Values are for the MG90S servo
 [servo ercf_servo]
-pin: ercf:PA5
+pin: ercf:gpio21
 maximum_servo_angle: 180
 minimum_pulse_width: 0.00085
 maximum_pulse_width: 0.00215
 
 [duplicate_pin_override]
-pins: ercf:PA6
+pins: ercf:gpio15
 # Put there the pin used by the encoder and the filament_motion_sensor
 # It has to be the same pin for those 3
 
 [filament_motion_sensor encoder_sensor]
-switch_pin: ^ercf:PA6
+switch_pin: ^ercf:gpio15
 pause_on_runout: False
 detection_length: 10.0
 extruder: extruder
 # runout_gcode: _ERCF_ENCODER_MOTION_ISSUE
 
-[filament_switch_sensor toolhead_sensor]
-pause_on_runout: False
-switch_pin: ^PG12
-# runout_gcode:
-#   M118 toolhead filament removed
-# insert_gcode:
-#   M118 toolhead filament inserted

ercf/software.cfg

@@ -4,7 +4,7 @@
 
 [ercf]
 # Encoder
-encoder_pin: ercf:PA6         # easy brd
+encoder_pin: ercf:gpio15      # easy brd
 # encoder_resolution: 1.365188 # in mm
 encoder_resolution: 1.349528  # from `ercf_calibrate_encoder`
 # Speeds and accels

printer.cfg

@@ -64,8 +64,7 @@ path: /home/pi/printer_data/gcodes
 [include fans.cfg]
 [include input_shaper.cfg]
 # [include resonance_test.cfg]
-[include ercf/hardware.cfg]
-[include ercf/software.cfg]
+[include ercf.cfg]
 
 
 #####################################################################