v2.4: add config, wip
This commit is contained in:
commit
9a1adc99ef
4 changed files with 746 additions and 0 deletions
70
fluidd.cfg
Normal file
70
fluidd.cfg
Normal file
|
|
@ -0,0 +1,70 @@
|
|||
[virtual_sdcard]
|
||||
path: /home/pi/gcode_files
|
||||
|
||||
[pause_resume]
|
||||
|
||||
[display_status]
|
||||
|
||||
[gcode_macro CANCEL_PRINT]
|
||||
description: Cancel the actual running print
|
||||
rename_existing: CANCEL_PRINT_BASE
|
||||
gcode:
|
||||
TURN_OFF_HEATERS
|
||||
CANCEL_PRINT_BASE
|
||||
|
||||
[gcode_macro PAUSE]
|
||||
description: Pause the actual running print
|
||||
rename_existing: PAUSE_BASE
|
||||
# change this if you need more or less extrusion
|
||||
variable_extrude: 1.0
|
||||
gcode:
|
||||
##### read E from pause macro #####
|
||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
||||
##### set park positon for x and y #####
|
||||
# default is your max posion from your printer.cfg
|
||||
{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
|
||||
{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
|
||||
##### calculate save lift position #####
|
||||
{% set max_z = printer.toolhead.axis_maximum.z|float %}
|
||||
{% set act_z = printer.toolhead.position.z|float %}
|
||||
{% if act_z < (max_z - 2.0) %}
|
||||
{% set z_safe = 2.0 %}
|
||||
{% else %}
|
||||
{% set z_safe = max_z - act_z %}
|
||||
{% endif %}
|
||||
##### end of definitions #####
|
||||
PAUSE_BASE
|
||||
G91
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G1 E-{E} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
{% if "xyz" in printer.toolhead.homed_axes %}
|
||||
G1 Z{z_safe} F900
|
||||
G90
|
||||
G1 X{x_park} Y{y_park} F6000
|
||||
{% else %}
|
||||
{action_respond_info("Printer not homed")}
|
||||
{% endif %}
|
||||
|
||||
[gcode_macro RESUME]
|
||||
description: Resume the actual running print
|
||||
rename_existing: RESUME_BASE
|
||||
gcode:
|
||||
##### read E from pause macro #####
|
||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
||||
#### get VELOCITY parameter if specified ####
|
||||
{% if 'VELOCITY' in params|upper %}
|
||||
{% set get_params = ('VELOCITY=' + params.VELOCITY) %}
|
||||
{%else %}
|
||||
{% set get_params = "" %}
|
||||
{% endif %}
|
||||
##### end of definitions #####
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G91
|
||||
G1 E{E} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
RESUME_BASE {get_params}
|
||||
40
moonraker.conf
Normal file
40
moonraker.conf
Normal file
|
|
@ -0,0 +1,40 @@
|
|||
[server]
|
||||
host: 0.0.0.0
|
||||
port: 7125
|
||||
enable_debug_logging: False
|
||||
config_path: ~/klipper_config
|
||||
temperature_store_size: 600
|
||||
gcode_store_size: 1000
|
||||
log_path: ~/klipper_logs
|
||||
|
||||
[authorization]
|
||||
force_logins: True
|
||||
cors_domains:
|
||||
*.local
|
||||
*.lan
|
||||
*://app.fluidd.xyz
|
||||
|
||||
trusted_clients:
|
||||
10.0.0.0/8
|
||||
127.0.0.0/8
|
||||
169.254.0.0/16
|
||||
172.16.0.0/12
|
||||
192.168.0.0/16
|
||||
FE80::/10
|
||||
::1/128
|
||||
|
||||
# enables partial support of Octoprint API
|
||||
[octoprint_compat]
|
||||
|
||||
# enables moonraker to track and store print history.
|
||||
[history]
|
||||
|
||||
# this enables moonraker's update manager
|
||||
[update_manager]
|
||||
enable_auto_refresh: True
|
||||
|
||||
# this enabled fluidd updates
|
||||
[update_manager client fluidd]
|
||||
type: web
|
||||
repo: cadriel/fluidd
|
||||
path: ~/fluidd
|
||||
557
printer.cfg
Normal file
557
printer.cfg
Normal file
|
|
@ -0,0 +1,557 @@
|
|||
# This file contains common pin mappings for the BigTreeTech OctoPus V1.
|
||||
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
|
||||
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
|
||||
|
||||
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
|
||||
|
||||
## *** THINGS TO CHANGE/CHECK: ***
|
||||
## MCU paths [mcu] section
|
||||
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
||||
## Z Endstop Switch location [safe_z_home] section
|
||||
## Homing end position [gcode_macro G32] section
|
||||
## Z Endstop Switch offset for Z0 [stepper_z] section
|
||||
## Probe points [quad_gantry_level] section
|
||||
## Min & Max gantry corner postions [quad_gantry_level] section
|
||||
## PID tune [extruder] and [heater_bed] sections
|
||||
## Fine tune E steps [extruder] section
|
||||
|
||||
[mcu]
|
||||
## [X in MOTOR0] - B Motor
|
||||
## [Y in MOTOR1] - A Motor
|
||||
## [E in MOTOR6] - Extruder
|
||||
## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
|
||||
##--------------------------------------------------------------------
|
||||
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_1E0030000E5053424E363620-if00
|
||||
#restart_method: command
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
[include fluidd.cfg]
|
||||
|
||||
[printer]
|
||||
kinematics: corexy
|
||||
max_velocity: 300
|
||||
max_accel: 3000 #Max 4000
|
||||
max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V
|
||||
max_z_accel: 350
|
||||
square_corner_velocity: 5.0
|
||||
|
||||
#####################################################################
|
||||
# X/Y Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## X Stepper on MOTOR0(B Motor)
|
||||
[stepper_x]
|
||||
step_pin: PF13
|
||||
dir_pin: !PF12
|
||||
enable_pin: !PF14
|
||||
rotation_distance: 40
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 400 # 200: 1.8 deg stepper, 400: 0.9 deg stepper
|
||||
endstop_pin: PG6
|
||||
position_min: 0
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
## Uncomment below for 250mm build
|
||||
#position_endstop: 250
|
||||
#position_max: 250
|
||||
|
||||
## Uncomment for 300mm build
|
||||
position_endstop: 300
|
||||
position_max: 300
|
||||
|
||||
## Uncomment for 350mm build
|
||||
#position_endstop: 350
|
||||
#position_max: 350
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
homing_speed: 25 #Max 100
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PC4
|
||||
interpolate: True
|
||||
run_current: 0.8
|
||||
hold_current: 0.7
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Y Stepper on MOTOR1 (A Motor)
|
||||
[stepper_y]
|
||||
step_pin: PG0
|
||||
dir_pin: !PG1
|
||||
enable_pin: !PF15
|
||||
rotation_distance: 40
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 400 # 200: 1.8 deg stepper, 400: 0.9 deg stepper
|
||||
endstop_pin: PG9
|
||||
position_min: 0
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
## Uncomment for 250mm build
|
||||
#position_endstop: 250
|
||||
#position_max: 250
|
||||
|
||||
## Uncomment for 300mm build
|
||||
position_endstop: 305
|
||||
position_max: 305
|
||||
|
||||
## Uncomment for 350mm build
|
||||
#position_endstop: 350
|
||||
#position_max: 350
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
homing_speed: 25 #Max 100
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PD11
|
||||
interpolate: True
|
||||
run_current: 0.8
|
||||
hold_current: 0.7
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
#####################################################################
|
||||
# Z Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## Z0 Stepper - Front Left on MOTOR2_1
|
||||
[stepper_z]
|
||||
step_pin: PF11
|
||||
# dir_pin: !PG3
|
||||
dir_pin: PG3
|
||||
enable_pin: !PG5
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
endstop_pin: PG10
|
||||
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||
## (+) value = endstop above Z0, (-) value = endstop below
|
||||
## Increasing position_endstop brings nozzle closer to the bed
|
||||
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
||||
position_endstop: -0.5
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
## Uncomment below for 250mm build
|
||||
#position_max: 240
|
||||
|
||||
## Uncomment below for 300mm build
|
||||
position_max: 290
|
||||
|
||||
## Uncomment below for 350mm build
|
||||
#position_max: 340
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
position_min: -5
|
||||
homing_speed: 8
|
||||
second_homing_speed: 3
|
||||
homing_retract_dist: 3
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PC6
|
||||
interpolate: true
|
||||
run_current: 0.8
|
||||
hold_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z1 Stepper - Rear Left on MOTOR3
|
||||
[stepper_z1]
|
||||
step_pin: PG4
|
||||
# dir_pin: PC1
|
||||
dir_pin: !PC1
|
||||
enable_pin: !PA0
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_z1]
|
||||
uart_pin: PC7
|
||||
interpolate: true
|
||||
run_current: 0.8
|
||||
hold_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z2 Stepper - Rear Right on MOTOR4
|
||||
[stepper_z2]
|
||||
step_pin: PF9
|
||||
# dir_pin: !PF10
|
||||
dir_pin: PF10
|
||||
enable_pin: !PG2
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_z2]
|
||||
uart_pin: PF2
|
||||
interpolate: true
|
||||
run_current: 0.8
|
||||
hold_current: 0.80
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z3 Stepper - Front Right on MOTOR5
|
||||
[stepper_z3]
|
||||
step_pin: PC13
|
||||
# dir_pin: PF0
|
||||
dir_pin: !PF0
|
||||
enable_pin: !PF1
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 stepper_z3]
|
||||
uart_pin: PE4
|
||||
interpolate: true
|
||||
run_current: 0.8
|
||||
hold_current: 0.80
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Extruder
|
||||
#####################################################################
|
||||
|
||||
# E0 on MOTOR6
|
||||
[extruder]
|
||||
step_pin: PE2
|
||||
dir_pin: PE3
|
||||
enable_pin: !PD4
|
||||
## Update value below when you perform extruder calibration
|
||||
## If you ask for 100mm of filament, but in reality it is 98mm:
|
||||
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
||||
## 22.6789511 is a good starting point
|
||||
rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears
|
||||
## Update Gear Ratio depending on your Extruder Type
|
||||
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
|
||||
## Use 80:20 for M4, M3.1
|
||||
gear_ratio: 50:17 #BMG Gear Ratio
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.75
|
||||
heater_pin: PA2
|
||||
## Validate the following thermistor type to make sure it is correct
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: PF4
|
||||
min_temp: 10
|
||||
max_temp: 270
|
||||
max_power: 1.0
|
||||
min_extrude_temp: 170
|
||||
control = pid
|
||||
pid_kp = 26.213
|
||||
pid_ki = 1.304
|
||||
pid_kd = 131.721
|
||||
## Try to keep pressure_advance below 1.0
|
||||
pressure_advance: 0.05
|
||||
## Default is 0.040, leave stock
|
||||
pressure_advance_smooth_time: 0.040
|
||||
|
||||
## E0 on MOTOR6
|
||||
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PE1
|
||||
interpolate: false
|
||||
run_current: 0.5
|
||||
hold_current: 0.4
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Bed Heater
|
||||
#####################################################################
|
||||
|
||||
[heater_bed]
|
||||
## SSR Pin - BED_OUT
|
||||
heater_pin: PA1
|
||||
sensor_type: NTC 100K beta 3950
|
||||
sensor_pin: PF3
|
||||
## Adjust Max Power so your heater doesn't warp your bed
|
||||
max_power: 0.6
|
||||
min_temp: 0
|
||||
max_temp: 120
|
||||
control: pid
|
||||
pid_kp: 58.437
|
||||
pid_ki: 2.347
|
||||
pid_kd: 363.769
|
||||
|
||||
#####################################################################
|
||||
# Probe
|
||||
#####################################################################
|
||||
|
||||
[probe]
|
||||
## Inductive Probe
|
||||
## This probe is not used for Z height, only Quad Gantry Leveling
|
||||
pin: ~!PB7
|
||||
x_offset: 0
|
||||
y_offset: 25.0
|
||||
z_offset: 0
|
||||
speed: 10.0
|
||||
samples: 3
|
||||
samples_result: median
|
||||
sample_retract_dist: 3.0
|
||||
samples_tolerance: 0.006
|
||||
samples_tolerance_retries: 3
|
||||
|
||||
#####################################################################
|
||||
# Fan Control
|
||||
#####################################################################
|
||||
|
||||
[fan]
|
||||
## Print Cooling Fan - CNC_FAN0
|
||||
pin: PA8
|
||||
kick_start_time: 0.5
|
||||
## Depending on your fan, you may need to increase this value
|
||||
## if your fan will not start. Can change cycle_time (increase)
|
||||
## if your fan is not able to slow down effectively
|
||||
off_below: 0.10
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
## Hotend Fan - CNC_FAN1
|
||||
pin: PE5
|
||||
max_power: 1.0
|
||||
kick_start_time: 0.5
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
## If you are experiencing back flow, you can reduce fan_speed
|
||||
#fan_speed: 1.0
|
||||
|
||||
[heater_fan controller_fan]
|
||||
## Controller fan - CNC_FAN2
|
||||
pin: PD12
|
||||
kick_start_time: 0.5
|
||||
heater: heater_bed
|
||||
heater_temp: 45.0
|
||||
|
||||
#[heater_fan exhaust_fan]
|
||||
## Exhaust fan - CNC_FAN3
|
||||
#pin: PD13
|
||||
#max_power: 1.0
|
||||
#shutdown_speed: 0.0
|
||||
#kick_start_time: 5.0
|
||||
#heater: heater_bed
|
||||
#heater_temp: 60
|
||||
#fan_speed: 1.0
|
||||
|
||||
#####################################################################
|
||||
# LED Control
|
||||
#####################################################################
|
||||
|
||||
#[output_pin caselight]
|
||||
# Chamber Lighting - HE1 Connector (Optional)
|
||||
#pin: PA3
|
||||
#pwm:true
|
||||
#shutdown_value: 0
|
||||
#value:1
|
||||
#cycle_time: 0.01
|
||||
|
||||
#####################################################################
|
||||
# Homing and Gantry Adjustment Routines
|
||||
#####################################################################
|
||||
|
||||
[idle_timeout]
|
||||
timeout: 1800
|
||||
|
||||
[safe_z_home]
|
||||
## XY Location of the Z Endstop Switch
|
||||
## Update -10,-10 to the XY coordinates of your endstop pin
|
||||
## (such as 157,305) after going through Z Endstop Pin
|
||||
## Location Definition step.
|
||||
home_xy_position: 208, 305
|
||||
speed:100
|
||||
z_hop:10
|
||||
|
||||
[quad_gantry_level]
|
||||
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
||||
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
||||
## to respective belt positions
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
## Gantry Corners for 250mm Build
|
||||
## Uncomment for 250mm build
|
||||
#gantry_corners:
|
||||
# -60,-10
|
||||
# 310, 320
|
||||
## Probe points
|
||||
#points:
|
||||
# 50,25
|
||||
# 50,175
|
||||
# 200,175
|
||||
# 200,25
|
||||
|
||||
## Gantry Corners for 300mm Build
|
||||
## Uncomment for 300mm build
|
||||
gantry_corners:
|
||||
-60,-10
|
||||
360,370
|
||||
# Probe points
|
||||
points:
|
||||
50,25
|
||||
50,225
|
||||
250,225
|
||||
250,25
|
||||
|
||||
## Gantry Corners for 350mm Build
|
||||
## Uncomment for 350mm build
|
||||
#gantry_corners:
|
||||
# -60,-10
|
||||
# 410,420
|
||||
## Probe points
|
||||
#points:
|
||||
# 50,25
|
||||
# 50,275
|
||||
# 300,275
|
||||
# 300,25
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
speed: 100
|
||||
horizontal_move_z: 10
|
||||
retries: 5
|
||||
retry_tolerance: 0.0075
|
||||
max_adjust: 10
|
||||
|
||||
########################################
|
||||
# EXP1 / EXP2 (display) pins
|
||||
########################################
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PE8, EXP1_2=PE7,
|
||||
EXP1_3=PE9, EXP1_4=PE10,
|
||||
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
|
||||
EXP1_7=PE14, EXP1_8=PE15,
|
||||
EXP1_9=<GND>, EXP1_10=<5V>,
|
||||
|
||||
# EXP2 header
|
||||
EXP2_1=PA6, EXP2_2=PA5,
|
||||
EXP2_3=PB1, EXP2_4=PA4,
|
||||
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
|
||||
EXP2_7=PC15, EXP2_8=<RST>,
|
||||
EXP2_9=<GND>, EXP2_10=<5V>
|
||||
|
||||
#####################################################################
|
||||
# Displays
|
||||
#####################################################################
|
||||
|
||||
## Uncomment the display that you have
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
#[display]
|
||||
## RepRapDiscount 128x64 Full Graphic Smart Controller
|
||||
#lcd_type: st7920
|
||||
#cs_pin: EXP1_4
|
||||
#sclk_pin: EXP1_5
|
||||
#sid_pin: EXP1_3
|
||||
#menu_timeout: 40
|
||||
#encoder_pins: ^EXP2_5, ^EXP2_3
|
||||
#click_pin: ^!EXP1_2
|
||||
|
||||
#[output_pin beeper]
|
||||
#pin: EXP1_1
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
#[display]
|
||||
## mini12864 LCD Display
|
||||
#lcd_type: uc1701
|
||||
#cs_pin: EXP1_3
|
||||
#a0_pin: EXP1_4
|
||||
#rst_pin: EXP1_5
|
||||
#encoder_pins: ^EXP2_5, ^EXP2_3
|
||||
#click_pin: ^!EXP1_2
|
||||
#contrast: 63
|
||||
#spi_software_miso_pin: EXP2_1
|
||||
#spi_software_mosi_pin: EXP2_6
|
||||
#spi_software_sclk_pin: EXP2_2
|
||||
|
||||
#[neopixel btt_mini12864]
|
||||
## To control Neopixel RGB in mini12864 display
|
||||
#pin: EXP1_6
|
||||
#chain_count: 3
|
||||
#initial_RED: 0.1
|
||||
#initial_GREEN: 0.5
|
||||
#initial_BLUE: 0.0
|
||||
#color_order: RGB
|
||||
|
||||
## Set RGB values on boot up for each Neopixel.
|
||||
## Index 1 = display, Index 2 and 3 = Knob
|
||||
#[delayed_gcode setdisplayneopixel]
|
||||
#initial_duration: 1
|
||||
#gcode:
|
||||
# SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
|
||||
# SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
|
||||
# SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Macros
|
||||
#####################################################################
|
||||
|
||||
[gcode_macro G32]
|
||||
gcode:
|
||||
BED_MESH_CLEAR
|
||||
G28
|
||||
QUAD_GANTRY_LEVEL
|
||||
G28
|
||||
## Uncomment for for your size printer:
|
||||
#--------------------------------------------------------------------
|
||||
## Uncomment for 250mm build
|
||||
#G0 X125 Y125 Z30 F3600
|
||||
|
||||
## Uncomment for 300 build
|
||||
G0 X150 Y150 Z30 F3600
|
||||
|
||||
## Uncomment for 350mm build
|
||||
#G0 X175 Y175 Z30 F3600
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
[gcode_macro PRINT_START]
|
||||
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
||||
gcode:
|
||||
G32 ; home all axes
|
||||
G1 Z20 F3000 ; move nozzle away from bed
|
||||
|
||||
|
||||
[gcode_macro PRINT_END]
|
||||
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
||||
gcode:
|
||||
M400 ; wait for buffer to clear
|
||||
G92 E0 ; zero the extruder
|
||||
G1 E-10.0 F3600 ; retract filament
|
||||
G91 ; relative positioning
|
||||
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
||||
TURN_OFF_HEATERS
|
||||
M107 ; turn off fan
|
||||
G1 Z2 F3000 ; move nozzle up 2mm
|
||||
G90 ; absolute positioning
|
||||
G0 X125 Y250 F3600 ; park nozzle at rear
|
||||
BED_MESH_CLEAR
|
||||
|
||||
## Thermistor Types
|
||||
## "EPCOS 100K B57560G104F"
|
||||
## "ATC Semitec 104GT-2"
|
||||
## "NTC 100K beta 3950"
|
||||
## "Honeywell 100K 135-104LAG-J01"
|
||||
## "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
|
||||
## "AD595"
|
||||
## "PT100 INA826"
|
||||
79
webcam.txt
Normal file
79
webcam.txt
Normal file
|
|
@ -0,0 +1,79 @@
|
|||
### Windows users: To edit this file use Notepad++, VSCode, Atom or SublimeText.
|
||||
### Do not use Notepad or WordPad.
|
||||
|
||||
### MacOSX users: If you use Textedit to edit this file make sure to use
|
||||
### "plain text format" and "disable smart quotes" in "Textedit > Preferences"
|
||||
|
||||
### Configure which camera to use
|
||||
#
|
||||
# Available options are:
|
||||
# - auto: tries first usb webcam, if that's not available tries raspi cam
|
||||
# - usb: only tries usb webcam
|
||||
# - raspi: only tries raspi cam
|
||||
#
|
||||
# Defaults to auto
|
||||
#
|
||||
#camera="auto"
|
||||
|
||||
### Additional options to supply to MJPG Streamer for the USB camera
|
||||
#
|
||||
# See https://faq.octoprint.org/mjpg-streamer-config for available options
|
||||
#
|
||||
# Defaults to a resolution of 640x480 px and a framerate of 10 fps
|
||||
#
|
||||
#camera_usb_options="-r 640x480 -f 10"
|
||||
|
||||
### Additional webcam devices known to cause problems with -f
|
||||
#
|
||||
# Apparently there a some devices out there that with the current
|
||||
# mjpg_streamer release do not support the -f parameter (for specifying
|
||||
# the capturing framerate) and will just refuse to output an image if it
|
||||
# is supplied.
|
||||
#
|
||||
# The webcam daemon will detect those devices by their USB Vendor and Product
|
||||
# ID and remove the -f parameter from the options provided to mjpg_streamer.
|
||||
#
|
||||
# By default, this is done for the following devices:
|
||||
# Logitech C170 (046d:082b)
|
||||
# GEMBIRD (1908:2310)
|
||||
# Genius F100 (0458:708c)
|
||||
# Cubeternet GL-UPC822 UVC WebCam (1e4e:0102)
|
||||
#
|
||||
# Using the following option it is possible to add additional devices. If
|
||||
# your webcam happens to show above symptoms, try determining your cam's
|
||||
# vendor and product id via lsusb, activating the line below by removing # and
|
||||
# adding it, e.g. for two broken cameras "aabb:ccdd" and "aabb:eeff"
|
||||
#
|
||||
# additional_brokenfps_usb_devices=("aabb:ccdd" "aabb:eeff")
|
||||
#
|
||||
#
|
||||
#additional_brokenfps_usb_devices=()
|
||||
|
||||
### Additional options to supply to MJPG Streamer for the RasPi Cam
|
||||
#
|
||||
# See https://faq.octoprint.org/mjpg-streamer-config for available options
|
||||
#
|
||||
# Defaults to 10fps
|
||||
#
|
||||
#camera_raspi_options="-fps 10"
|
||||
|
||||
### Configuration of camera HTTP output
|
||||
#
|
||||
# Usually you should NOT need to change this at all! Only touch if you
|
||||
# know what you are doing and what the parameters mean.
|
||||
#
|
||||
# Below settings are used in the mjpg-streamer call like this:
|
||||
#
|
||||
# -o "output_http.so -w $camera_http_webroot $camera_http_options"
|
||||
#
|
||||
# Current working directory is the mjpg-streamer base directory.
|
||||
#
|
||||
#camera_http_webroot="./www-fluidd"
|
||||
#camera_http_options="-n"
|
||||
|
||||
### EXPERIMENTAL
|
||||
# Support for different streamer types.
|
||||
#
|
||||
# Available options:
|
||||
# mjpeg [default] - stable MJPG-streamer
|
||||
#camera_streamer=mjpeg
|
||||
Loading…
Reference in a new issue