75 lines
2 KiB
INI
75 lines
2 KiB
INI
## Enraged Rabbit : Carrot Feeder config file for ERCF EASY BRD v1.1
|
|
|
|
# This config sample assume you set the two J6 jumpers on 1-2 and 4-5, i.e. [..].[..]
|
|
|
|
# Carrot Feeder 5mm D-cut shaft
|
|
[manual_stepper gear_stepper]
|
|
step_pin: ercf:gpio7
|
|
dir_pin: !ercf:gpio8
|
|
enable_pin: !ercf:gpio6
|
|
rotation_distance: 22.6789511 # Bondtech 5mm Drive Gears
|
|
gear_ratio: 80:20
|
|
microsteps: 16
|
|
full_steps_per_rotation: 200
|
|
velocity: 35
|
|
accel: 100
|
|
endstop_pin: ercf:gpio13
|
|
|
|
[tmc2209 manual_stepper gear_stepper]
|
|
# Adapt accordingly to your setup and desires
|
|
# The default values are tested with the BOM NEMA14 motor
|
|
uart_pin: ercf:gpio9
|
|
interpolate: True
|
|
run_current: 0.6
|
|
hold_current: 0.1
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 500
|
|
# diag_pin: ercf:gpio23
|
|
|
|
[manual_stepper selector_stepper]
|
|
step_pin: ercf:gpio2
|
|
dir_pin: !ercf:gpio1
|
|
enable_pin: !ercf:gpio3
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
full_steps_per_rotation: 200
|
|
velocity: 200
|
|
homing_speed: 100
|
|
accel: 600
|
|
# Select the endstop you want depending if you are using sensorless homing
|
|
# endstop_pin: ^ercf:PB9
|
|
endstop_pin: ercf:gpio20
|
|
#endstop_pin: tmc2209_selector_stepper:virtual_endstop
|
|
#endstop_pin: tmc5160_selector_stepper:virtual_endstop
|
|
|
|
[tmc2209 manual_stepper selector_stepper]
|
|
uart_pin: ercf:gpio0
|
|
run_current: 0.55
|
|
hold_current: 0.4
|
|
interpolate: True
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 5000
|
|
# Uncomment the lines below if you want to use sensorless homing for the selector
|
|
# diag_pin: ^ercf:gpio22 # Set to MCU pin connected to TMC DIAG pin
|
|
# driver_SGTHRS: 75 # 255 is most sensitive value, 0 is least sensitive
|
|
|
|
|
|
# Values are for the MG90S servo
|
|
[servo ercf_servo]
|
|
pin: ercf:gpio21
|
|
maximum_servo_angle: 180
|
|
minimum_pulse_width: 0.00085
|
|
maximum_pulse_width: 0.00215
|
|
|
|
[duplicate_pin_override]
|
|
pins: ercf:gpio15
|
|
# Put there the pin used by the encoder and the filament_motion_sensor
|
|
# It has to be the same pin for those 3
|
|
|
|
[filament_motion_sensor encoder_sensor]
|
|
switch_pin: ^ercf:gpio15
|
|
pause_on_runout: False
|
|
detection_length: 10.0
|
|
extruder: extruder
|
|
# runout_gcode: _ERCF_ENCODER_MOTION_ISSUE
|
|
|