484 lines
12 KiB
INI
484 lines
12 KiB
INI
# This file contains common pin mappings for the BigTreeTech OctoPus V1.
|
|
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
|
|
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
|
|
|
|
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
|
|
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
|
|
|
|
## *** THINGS TO CHANGE/CHECK: ***
|
|
## MCU paths [mcu] section
|
|
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
|
## Z Endstop Switch location [safe_z_home] section
|
|
## Homing end position [gcode_macro G32] section
|
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
|
## Probe points [quad_gantry_level] section
|
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
|
## PID tune [extruder] and [heater_bed] sections
|
|
## Fine tune E steps [extruder] section
|
|
|
|
[mcu]
|
|
## [X in MOTOR0] - B Motor
|
|
## [Y in MOTOR1] - A Motor
|
|
## [E in MOTOR6] - Extruder
|
|
## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
|
|
##--------------------------------------------------------------------
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_1E0030000E5053424E363620-if00
|
|
#restart_method: command
|
|
##--------------------------------------------------------------------
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 300
|
|
max_accel: 3000 # Max 4000
|
|
max_accel_to_decel: 1500 # default half of max_accel
|
|
max_z_velocity: 25 # Max 15 for 12V TMC Drivers, can increase for 24V
|
|
max_z_accel: 350
|
|
square_corner_velocity: 5.0
|
|
|
|
|
|
#####################################################################
|
|
# fluidd
|
|
#####################################################################
|
|
|
|
[include fluidd.cfg]
|
|
|
|
|
|
#####################################################################
|
|
# Macros
|
|
#####################################################################
|
|
|
|
[include macros.cfg]
|
|
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
## X Stepper on MOTOR0(B Motor)
|
|
[stepper_x]
|
|
step_pin: PF13
|
|
dir_pin: !PF12
|
|
enable_pin: !PF14
|
|
rotation_distance: 40
|
|
microsteps: 16
|
|
full_steps_per_rotation: 400 # 1.8 deg stepper: 200, 0.9 deg stepper
|
|
endstop_pin: PG6
|
|
position_min: 0
|
|
position_endstop: 300
|
|
position_max: 300
|
|
homing_speed: 25 # Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC4
|
|
interpolate: True
|
|
run_current: 0.8
|
|
hold_current: 0.7
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Y Stepper on MOTOR1 (A Motor)
|
|
[stepper_y]
|
|
step_pin: PG0
|
|
dir_pin: !PG1
|
|
enable_pin: !PF15
|
|
rotation_distance: 40
|
|
microsteps: 16
|
|
full_steps_per_rotation: 400 # 200: 1.8 deg stepper, 400: 0.9 deg stepper
|
|
endstop_pin: PG9
|
|
position_min: 0
|
|
position_endstop: 305
|
|
position_max: 305
|
|
homing_speed: 25 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PD11
|
|
interpolate: True
|
|
run_current: 0.8
|
|
hold_current: 0.7
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## Z0 Stepper - Front Left on MOTOR2_1
|
|
[stepper_z]
|
|
step_pin: PF11
|
|
dir_pin: PG3
|
|
enable_pin: !PG5
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
endstop_pin: PG10
|
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
## (+) value = endstop above Z0, (-) value = endstop below
|
|
## Increasing position_endstop brings nozzle closer to the bed
|
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
#position_endstop: -0.5
|
|
position_max: 290
|
|
position_min: -5
|
|
homing_speed: 8
|
|
second_homing_speed: 3
|
|
homing_retract_dist: 3
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC6
|
|
interpolate: true
|
|
run_current: 0.8
|
|
hold_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z1 Stepper - Rear Left on MOTOR3
|
|
[stepper_z1]
|
|
step_pin: PG4
|
|
dir_pin: !PC1
|
|
enable_pin: !PA0
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: PC7
|
|
interpolate: true
|
|
run_current: 0.8
|
|
hold_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z2 Stepper - Rear Right on MOTOR4
|
|
[stepper_z2]
|
|
step_pin: PF9
|
|
dir_pin: PF10
|
|
enable_pin: !PG2
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: PF2
|
|
interpolate: true
|
|
run_current: 0.8
|
|
hold_current: 0.80
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## Z3 Stepper - Front Right on MOTOR5
|
|
[stepper_z3]
|
|
step_pin: PC13
|
|
dir_pin: !PF0
|
|
enable_pin: !PF1
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: PE4
|
|
interpolate: true
|
|
run_current: 0.8
|
|
hold_current: 0.80
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
|
|
#####################################################################
|
|
# Extruder
|
|
#####################################################################
|
|
|
|
# E0 on MOTOR6
|
|
[extruder]
|
|
step_pin: PE2
|
|
dir_pin: !PE3
|
|
enable_pin: !PD4
|
|
## Update value below when you perform extruder calibration
|
|
## If you ask for 100mm of filament, but in reality it is 98mm:
|
|
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
|
## 22.6789511 is a good starting point
|
|
rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears
|
|
## Update Gear Ratio depending on your Extruder Type
|
|
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
|
|
## Use 80:20 for M4, M3.1
|
|
gear_ratio: 50:17 # BMG Gear Ratio
|
|
microsteps: 16
|
|
full_steps_per_rotation: 200 # 1.8 deg stepper: 200, 0.9 deg stepper
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.75
|
|
heater_pin: PA2
|
|
## Validate the following thermistor type to make sure it is correct
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: PF4
|
|
min_temp: 10
|
|
max_temp: 270
|
|
max_power: 1.0
|
|
min_extrude_temp: 170
|
|
#control = pid
|
|
#pid_kp = 26.213
|
|
#pid_ki = 1.304
|
|
#pid_kd = 131.721
|
|
## Try to keep pressure_advance below 1.0
|
|
pressure_advance: 0.05
|
|
## Default is 0.040, leave stock
|
|
pressure_advance_smooth_time: 0.040
|
|
|
|
## E0 on MOTOR6
|
|
[tmc2209 extruder]
|
|
uart_pin: PE1
|
|
interpolate: false
|
|
run_current: 0.5
|
|
hold_current: 0.4
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
[heater_bed]
|
|
## SSR Pin - BED_OUT
|
|
heater_pin: PA1
|
|
sensor_type: NTC 100K beta 3950
|
|
sensor_pin: PF3
|
|
## Adjust Max Power so your heater doesn't warp your bed
|
|
max_power: 0.8 # 0.4W per cm2, 360W for 300 build
|
|
min_temp: 0
|
|
max_temp: 120
|
|
#control: pid
|
|
#pid_kp: 58.437
|
|
#pid_ki: 2.347
|
|
#pid_kd: 363.769
|
|
|
|
|
|
#####################################################################
|
|
# Probe
|
|
#####################################################################
|
|
|
|
[probe]
|
|
## Inductive Probe
|
|
## This probe is not used for Z height, only Quad Gantry Leveling
|
|
pin: ~PB7
|
|
x_offset: 0
|
|
y_offset: 25.0
|
|
z_offset: 0
|
|
speed: 10.0
|
|
samples: 3
|
|
samples_result: median
|
|
sample_retract_dist: 3.0
|
|
samples_tolerance: 0.006
|
|
samples_tolerance_retries: 3
|
|
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
[fan]
|
|
## Print Cooling Fan - CNC_FAN0
|
|
pin: PA8
|
|
kick_start_time: 0.5
|
|
## Depending on your fan, you may need to increase this value
|
|
## if your fan will not start. Can change cycle_time (increase)
|
|
## if your fan is not able to slow down effectively
|
|
off_below: 0.10
|
|
|
|
[heater_fan hotend_fan]
|
|
## Hotend Fan - CNC_FAN1
|
|
pin: PE5
|
|
max_power: 1.0
|
|
kick_start_time: 0.5
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
## If you are experiencing back flow, you can reduce fan_speed
|
|
#fan_speed: 1.0
|
|
|
|
[heater_fan controller_fan]
|
|
## Controller fan - CNC_FAN2
|
|
pin: PD12
|
|
kick_start_time: 0.5
|
|
heater: heater_bed
|
|
heater_temp: 45.0
|
|
|
|
#[heater_fan exhaust_fan]
|
|
## Exhaust fan - CNC_FAN3
|
|
#pin: PD13
|
|
#max_power: 1.0
|
|
#shutdown_speed: 0.0
|
|
#kick_start_time: 5.0
|
|
#heater: heater_bed
|
|
#heater_temp: 60
|
|
#fan_speed: 1.0
|
|
|
|
|
|
#####################################################################
|
|
# LED Control
|
|
#####################################################################
|
|
|
|
#[output_pin caselight]
|
|
# Chamber Lighting - HE1 Connector (Optional)
|
|
#pin: PA3
|
|
#pwm:true
|
|
#shutdown_value: 0
|
|
#value:1
|
|
#cycle_time: 0.01
|
|
|
|
|
|
#####################################################################
|
|
# Homing and Gantry Adjustment Routines
|
|
#####################################################################
|
|
|
|
|
|
#####################################################################
|
|
# Enclosure Temp Sensor Section
|
|
#####################################################################
|
|
[thermistor chamber_temp]
|
|
temperature1: 25
|
|
resistance1: 10000
|
|
beta: 3950
|
|
|
|
|
|
[temperature_sensor enclosure_temp]
|
|
sensor_type: chamber_temp
|
|
sensor_pin: PF5
|
|
min_temp: 0
|
|
max_temp: 100
|
|
gcode_id: C
|
|
|
|
[idle_timeout]
|
|
timeout: 1800
|
|
|
|
[safe_z_home]
|
|
## XY Location of the Z Endstop Switch
|
|
home_xy_position: 208, 305
|
|
speed:100
|
|
z_hop:10
|
|
|
|
[bed_mesh]
|
|
speed: 300
|
|
horizontal_move_z: 10
|
|
mesh_min: 40,40
|
|
mesh_max: 260,260
|
|
fade_start: 0.6
|
|
fade_end: 10
|
|
probe_count: 5,5
|
|
algorithm: bicubic
|
|
relative_reference_index: 12
|
|
|
|
[quad_gantry_level]
|
|
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
|
gantry_corners:
|
|
-60,-10
|
|
360,370
|
|
points:
|
|
50,25
|
|
50,225
|
|
250,225
|
|
250,25
|
|
speed: 100
|
|
horizontal_move_z: 10
|
|
retries: 5
|
|
retry_tolerance: 0.0075
|
|
max_adjust: 10
|
|
|
|
|
|
########################################
|
|
# EXP1 / EXP2 (display) pins
|
|
########################################
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PE8, EXP1_2=PE7,
|
|
EXP1_3=PE9, EXP1_4=PE10,
|
|
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
|
|
EXP1_7=PE14, EXP1_8=PE15,
|
|
EXP1_9=<GND>, EXP1_10=<5V>,
|
|
|
|
# EXP2 header
|
|
EXP2_1=PA6, EXP2_2=PA5,
|
|
EXP2_3=PB1, EXP2_4=PA4,
|
|
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
|
|
EXP2_7=PC15, EXP2_8=<RST>,
|
|
EXP2_9=<GND>, EXP2_10=<5V>
|
|
|
|
|
|
#####################################################################
|
|
# Displays
|
|
#####################################################################
|
|
|
|
[display]
|
|
# mini12864 LCD Display
|
|
lcd_type: uc1701
|
|
cs_pin: EXP1_3
|
|
a0_pin: EXP1_4
|
|
rst_pin: EXP1_5
|
|
encoder_pins: ^EXP2_5, ^EXP2_3
|
|
click_pin: ^!EXP1_2
|
|
contrast: 63
|
|
spi_software_miso_pin: EXP2_1
|
|
spi_software_mosi_pin: EXP2_6
|
|
spi_software_sclk_pin: EXP2_2
|
|
|
|
[neopixel btt_mini12864]
|
|
# To control Neopixel RGB in mini12864 display
|
|
pin: EXP1_6
|
|
chain_count: 3
|
|
initial_RED: 0.1
|
|
initial_GREEN: 0.5
|
|
initial_BLUE: 0.0
|
|
color_order: RGB
|
|
|
|
# Set RGB values on boot up for each Neopixel.
|
|
# Index 1 = display, Index 2 and 3 = Knob
|
|
[delayed_gcode setdisplayneopixel]
|
|
initial_duration: 1
|
|
gcode:
|
|
SET_LED LED=btt_mini12864 RED=0.50 GREEN=0.00 BLUE=0.00 INDEX=1 TRANSMIT=0
|
|
SET_LED LED=btt_mini12864 RED=0.13 GREEN=0.16 BLUE=1.00 INDEX=2 TRANSMIT=0
|
|
SET_LED LED=btt_mini12864 RED=0.13 GREEN=0.16 BLUE=1.00 INDEX=3
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 37.870
|
|
#*# pid_ki = 1.244
|
|
#*# pid_kd = 288.283
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 27.483
|
|
#*# pid_ki = 1.762
|
|
#*# pid_kd = 107.182
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.085000, 0.102500, 0.075000, 0.080000, 0.060000
|
|
#*# 0.057500, 0.062500, 0.020000, 0.032500, 0.035000
|
|
#*# 0.027500, 0.035000, 0.000000, 0.000000, -0.007500
|
|
#*# 0.020000, 0.032500, -0.005000, 0.017500, 0.020000
|
|
#*# 0.072500, 0.085000, 0.045000, 0.057500, 0.057500
|
|
#*# tension = 0.2
|
|
#*# min_x = 40.0
|
|
#*# algo = bicubic
|
|
#*# y_count = 5
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 40.0
|
|
#*# x_count = 5
|
|
#*# max_y = 260.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 260.0
|
|
#*#
|
|
#*# [stepper_z]
|
|
#*# position_endstop = 0.642
|