58 lines
1.9 KiB
INI
58 lines
1.9 KiB
INI
# [mcu nano]
|
|
# serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
|
|
|
# [mcu pico]
|
|
# serial: /dev/serial/by-id/usb-Klipper_rp2040_E660583883511936-if00
|
|
|
|
# [board_pins arduino]
|
|
# mcu: nano
|
|
# aliases:
|
|
# ar0=PD0, ar1=PD1, ar2=PD2, ar3=PD3, ar4=PD4,
|
|
# ar5=PD5, ar6=PD6, ar7=PD7, ar8=PB0, ar9=PB1,
|
|
# ar10=PB2, ar11=PB3, ar12=PB4, ar13=PB5, ar14=PC0,
|
|
# ar15=PC1, ar16=PC2, ar17=PC3, ar18=PC4, ar19=PC5,
|
|
# analog0=PC0, analog1=PC1, analog2=PC2, analog3=PC3, analog4=PC4,
|
|
# analog5=PC5, analog6=PE2, analog7=PE3
|
|
|
|
# [output_pin led]
|
|
# pin: nano:ar13
|
|
# value: 0
|
|
#
|
|
# ## arduino nano
|
|
# [adxl345]
|
|
# # The SPI enable pin for the sensor. This parameter must be provided.
|
|
# cs_pin: nano:ar10
|
|
# # The SPI speed (in hz) to use when communicating with the chip.
|
|
# # The default is 5000000.
|
|
# # spi_speed: 5000000
|
|
# # See the "common SPI settings" section for a description of the
|
|
# # above parameters.
|
|
# # spi_bus:
|
|
# spi_software_sclk_pin: nano:ar13
|
|
# spi_software_mosi_pin: nano:ar11
|
|
# spi_software_miso_pin: nano:ar12
|
|
# # The accelerometer axis for each of the printer's x, y, and z axes.
|
|
# # This may be useful if the accelerometer is mounted in an
|
|
# # orientation that does not match the printer orientation. For
|
|
# # example, one could set this to "y,x,z" to swap the x and y axes.
|
|
# # It is also possible to negate an axis if the accelerometer
|
|
# # direction is reversed (eg, "x,z,-y"). The default is "x,y,z".
|
|
# axes_map: x,z,-y
|
|
# # Output data rate for ADXL345. ADXL345 supports the following data
|
|
# # rates: 3200, 1600, 800, 400, 200, 100, 50, and 25. Note that it is
|
|
# # not recommended to change this rate from the default 3200, and
|
|
# # rates below 800 will considerably affect the quality of resonance
|
|
# # measurements.
|
|
# # rate: 3200
|
|
|
|
# ## rpi pico
|
|
# [adxl345]
|
|
# cs_pin: pico:gpio1
|
|
# spi_bus: spi0a
|
|
# axes_map: x,y,z
|
|
|
|
# [resonance_tester]
|
|
# accel_chip: adxl345
|
|
# probe_points:
|
|
# 150,150,20 # an example
|
|
|