260 lines
5.3 KiB
INI
260 lines
5.3 KiB
INI
##
|
|
# Prusa Mini+
|
|
##
|
|
|
|
## general configuration
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_2B0024001547393432343038-if00
|
|
restart_method: command
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
# Prusa firmware defaults.
|
|
max_velocity: 180
|
|
max_accel: 1250
|
|
max_z_velocity: 12
|
|
max_z_accel: 400
|
|
|
|
[virtual_sdcard]
|
|
path: ~/gcode_files
|
|
|
|
[save_variables]
|
|
filename: ~/klipper_config/variables.cfg
|
|
|
|
## neopixel
|
|
[include neopixel.cfg]
|
|
|
|
## macros
|
|
[include macros.cfg]
|
|
|
|
## display menu
|
|
[include display_menu.cfg]
|
|
|
|
## web
|
|
[pause_resume]
|
|
|
|
[display_status]
|
|
|
|
[respond]
|
|
default_type: echo
|
|
# Sets the default prefix of the "M118" and "RESPOND" output to one
|
|
# of the following:
|
|
# echo: "echo: " (This is the default)
|
|
# command: "// "
|
|
# error: "!! "
|
|
# default_prefix: echo:
|
|
# Directly sets the default prefix. If present, this value will
|
|
# override the "default_type".
|
|
|
|
## stepper
|
|
[stepper_x]
|
|
step_pin: PD1
|
|
dir_pin: PD0
|
|
enable_pin: !PD3
|
|
microsteps: 16
|
|
rotation_distance: 32 # 200 * 16 / 100
|
|
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
|
position_endstop: 180.4
|
|
position_min: -2
|
|
position_max: 180.4
|
|
homing_speed: 50
|
|
homing_retract_dist: 0
|
|
|
|
[stepper_y]
|
|
step_pin: PD13
|
|
dir_pin: PD12
|
|
enable_pin: !PD14
|
|
microsteps: 16
|
|
rotation_distance: 32 # 200 * 16 / 100
|
|
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
|
position_endstop: -3
|
|
position_min: -3
|
|
position_max: 180
|
|
homing_speed: 50
|
|
homing_retract_dist: 0
|
|
|
|
[stepper_z]
|
|
step_pin: PD4
|
|
dir_pin: !PD15
|
|
enable_pin: !PD2
|
|
microsteps: 16
|
|
rotation_distance: 4
|
|
endstop_pin: probe:z_virtual_endstop
|
|
position_min: -3
|
|
position_max: 185
|
|
|
|
## tmc
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PD5
|
|
uart_address: 1
|
|
diag_pin: ^PE2
|
|
driver_SGTHRS: 130
|
|
run_current: 0.35
|
|
sense_resistor: 0.22
|
|
stealthchop_threshold: 999999
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PD5
|
|
uart_address: 3
|
|
diag_pin: ^PE1
|
|
driver_SGTHRS: 130
|
|
run_current: 0.35
|
|
sense_resistor: 0.22
|
|
stealthchop_threshold: 999999
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PD5
|
|
uart_address: 0
|
|
diag_pin: ^PE3
|
|
driver_SGTHRS: 100
|
|
run_current: 0.35
|
|
sense_resistor: 0.22
|
|
stealthchop_threshold: 999999
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PD5
|
|
uart_address: 2
|
|
diag_pin: ^PA15
|
|
driver_SGTHRS: 100
|
|
run_current: 0.4
|
|
sense_resistor: 0.22
|
|
|
|
## display
|
|
[display]
|
|
lcd_type: st7789v
|
|
spi_bus: spi2a
|
|
rst_pin: PC8
|
|
cs_pin: PC9
|
|
rs_pin: PD11
|
|
encoder_pins: ^PE13, ^PE15
|
|
click_pin: ^!PE12
|
|
|
|
[extruder]
|
|
step_pin: PD9
|
|
dir_pin: !PD8
|
|
enable_pin: !PD10
|
|
microsteps: 16
|
|
rotation_distance: 26.2564 # (200 * 16 * 48/18) / 325
|
|
gear_ratio: 48:18
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PB1
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: PC0
|
|
# Prusa's firmware defaults.
|
|
#control: pid
|
|
#pid_Kp: 7
|
|
#pid_Ki: 0.5
|
|
#pid_Kd: 45
|
|
min_temp: 10
|
|
max_temp: 305
|
|
max_extrude_only_distance: 800.0
|
|
# max_extrude_cross_section: 10.0
|
|
|
|
[heater_bed]
|
|
heater_pin: PB0
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA4
|
|
# Prusa's firmware defaults.
|
|
#control: pid
|
|
#pid_Kp: 120
|
|
#pid_Ki: 1.5
|
|
#pid_Kd: 600
|
|
min_temp: 10
|
|
max_temp: 110
|
|
|
|
# Hotend fan.
|
|
# The stock firmware uses control ranges of PWM 0-50%, RPM 1000-8000.
|
|
# Change fan_speed below to match your preference. Measured speeds:
|
|
# fan_speed 0.5: 50% PWM = 4000RPM (Prusa stock default speed)
|
|
# fan_speed 1.0: 100% PWM = 8000RPM (safe but loud)
|
|
[heater_fan hotend_fan]
|
|
pin: PE9
|
|
tachometer_pin: PE14
|
|
fan_speed: 0.5
|
|
|
|
# Part cooling fan.
|
|
# The stock firmware uses control ranges of PWM 10-50%, RPM 500-5000.
|
|
# To match stock firmware, set the Klipper fan speed to 50%. This speed
|
|
# can be safely increased to 100% for better part cooling. Measured speeds:
|
|
# 50% PWM = 2500RPM (Prusa stock default speed)
|
|
# 100% PWM = 5000RPM (better cooling, still quiet)
|
|
[fan]
|
|
pin: PE11
|
|
tachometer_pin: PE10
|
|
|
|
# The SuperPINDA has built-in temperature compensation and no thermistor output,
|
|
# so no compensation table is needed here.
|
|
[probe]
|
|
pin: PA8
|
|
x_offset: -29
|
|
y_offset: -3
|
|
#z_offset: 0 # set this to your Live Z Offset, but negated (invert the sign)
|
|
speed: 6.0
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 160,20
|
|
z_hop: 4
|
|
|
|
[bed_mesh]
|
|
speed: 1000
|
|
horizontal_move_z: 5
|
|
mesh_min: 10,10
|
|
mesh_max: 141,167
|
|
probe_count: 5,5
|
|
algorithm: bicubic
|
|
|
|
[filament_switch_sensor filament_sensor]
|
|
switch_pin: ^PB4
|
|
pause_on_runout: True
|
|
event_delay: 3.0
|
|
pause_delay: 0.5
|
|
runout_gcode:
|
|
M117 filament removed
|
|
insert_gcode:
|
|
M117 filament inserted
|
|
G4 P3000
|
|
{% for i in range(10) %}
|
|
M117 loading in {10-i}
|
|
G4 P1000
|
|
{% endfor %}
|
|
M117 loading now
|
|
FILAMENT_LOAD
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 21.307
|
|
#*# pid_ki = 0.911
|
|
#*# pid_kd = 124.644
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 57.528
|
|
#*# pid_ki = 1.059
|
|
#*# pid_kd = 780.942
|
|
#*#
|
|
#*# [probe]
|
|
#*# z_offset = 1.480
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# -0.068750, -0.116250, 0.025000, 0.067500, -0.095000, 0.002500
|
|
#*# -0.048750, -0.036250, 0.005000, -0.028750, 0.032500, 0.086250
|
|
#*# -0.027500, -0.028750, -0.001250, 0.010000, 0.026250, 0.045000
|
|
#*# 0.006250, -0.023750, -0.021250, 0.020000, 0.017500, 0.046250
|
|
#*# -0.063750, -0.011250, -0.015000, -0.030000, 0.021250, 0.017500
|
|
#*# -0.056250, -0.150000, -0.012500, -0.010000, -0.067500, -0.021250
|
|
#*# tension = 0.2
|
|
#*# min_x = 10.0
|
|
#*# algo = bicubic
|
|
#*# y_count = 6
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 10.0
|
|
#*# x_count = 6
|
|
#*# max_y = 167.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 141.0
|