v2.4: clean-up

printer.cfg

@@ -40,6 +40,7 @@ max_z_velocity: 25 			#Max 15 for 12V TMC Drivers, can increase for 24V
 max_z_accel: 350
 square_corner_velocity: 5.0
 
+
 #####################################################################
 # 	X/Y Stepper Settings
 #####################################################################
@@ -54,26 +55,12 @@ microsteps: 16
 full_steps_per_rotation: 400  # 200: 1.8 deg stepper, 400: 0.9 deg stepper
 endstop_pin: PG6
 position_min: 0
-##--------------------------------------------------------------------
-
-##	Uncomment below for 250mm build
-#position_endstop: 250
-#position_max: 250
-
-##	Uncomment for 300mm build
 position_endstop: 300
 position_max: 300
-
-##	Uncomment for 350mm build
-#position_endstop: 350
-#position_max: 350
-
-##--------------------------------------------------------------------
 homing_speed: 25   #Max 100
 homing_retract_dist: 5
 homing_positive_dir: true
 
-##	Make sure to update below for your relevant driver (2208 or 2209)
 [tmc2209 stepper_x]
 uart_pin: PC4
 interpolate: True
@@ -92,26 +79,12 @@ microsteps: 16
 full_steps_per_rotation: 400  # 200: 1.8 deg stepper, 400: 0.9 deg stepper
 endstop_pin: PG9
 position_min: 0
-##--------------------------------------------------------------------
-
-##	Uncomment for 250mm build
-#position_endstop: 250
-#position_max: 250
-
-##	Uncomment for 300mm build
 position_endstop: 305
 position_max: 305
-
-##	Uncomment for 350mm build
-#position_endstop: 350
-#position_max: 350
-
-##--------------------------------------------------------------------
 homing_speed: 25  #Max 100
 homing_retract_dist: 5
 homing_positive_dir: true
 
-##	Make sure to update below for your relevant driver (2208 or 2209)
 [tmc2209 stepper_y]
 uart_pin: PD11
 interpolate: True
@@ -120,6 +93,7 @@ hold_current: 0.7
 sense_resistor: 0.110
 stealthchop_threshold: 0
  
+
 #####################################################################
 # 	Z Stepper Settings
 #####################################################################
@@ -127,7 +101,6 @@ stealthchop_threshold: 0
 ## Z0 Stepper - Front Left on MOTOR2_1
 [stepper_z]
 step_pin: PF11
-# dir_pin: !PG3
 dir_pin: PG3
 enable_pin: !PG5
 rotation_distance: 40
@@ -139,24 +112,12 @@ endstop_pin: PG10
 ##	Increasing position_endstop brings nozzle closer to the bed
 ##  After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
 position_endstop: -0.5
-##--------------------------------------------------------------------
-
-##	Uncomment below for 250mm build
-#position_max: 240
-
-##	Uncomment below for 300mm build
 position_max: 290
-
-##	Uncomment below for 350mm build
-#position_max: 340
-
-##--------------------------------------------------------------------
 position_min: -5
 homing_speed: 8
 second_homing_speed: 3
 homing_retract_dist: 3
 
-##	Make sure to update below for your relevant driver (2208 or 2209)
 [tmc2209 stepper_z]
 uart_pin: PC6
 interpolate: true
@@ -168,14 +129,12 @@ stealthchop_threshold: 0
 ##	Z1 Stepper - Rear Left on MOTOR3
 [stepper_z1]
 step_pin: PG4
-# dir_pin: PC1
 dir_pin: !PC1
 enable_pin: !PA0
 rotation_distance: 40
 gear_ratio: 80:16
 microsteps: 16
 
-##	Make sure to update below for your relevant driver (2208 or 2209)
 [tmc2209 stepper_z1]
 uart_pin: PC7
 interpolate: true
@@ -187,14 +146,12 @@ stealthchop_threshold: 0
 ##	Z2 Stepper - Rear Right on MOTOR4
 [stepper_z2]
 step_pin: PF9
-# dir_pin: !PF10
 dir_pin: PF10
 enable_pin: !PG2
 rotation_distance: 40
 gear_ratio: 80:16
 microsteps: 16
 
-##	Make sure to update below for your relevant driver (2208 or 2209)
 [tmc2209 stepper_z2]
 uart_pin: PF2
 interpolate: true
@@ -206,14 +163,12 @@ stealthchop_threshold: 0
 ##	Z3 Stepper - Front Right on MOTOR5
 [stepper_z3]
 step_pin: PC13
-# dir_pin: PF0
 dir_pin: !PF0
 enable_pin: !PF1
 rotation_distance: 40
 gear_ratio: 80:16
 microsteps: 16
 
-##	Make sure to update below for your relevant driver (2208 or 2209)
 [tmc2209 stepper_z3]
 uart_pin: PE4
 interpolate: true
@@ -263,7 +218,6 @@ pressure_advance: 0.05
 pressure_advance_smooth_time: 0.040
 
 ##	E0 on MOTOR6
-##	Make sure to update below for your relevant driver (2208 or 2209)
 [tmc2209 extruder]
 uart_pin: PE1
 interpolate: false
@@ -291,6 +245,7 @@ max_temp: 120
 #pid_ki: 2.347
 #pid_kd: 363.769
 
+
 #####################################################################
 # 	Probe
 #####################################################################
@@ -309,6 +264,7 @@ sample_retract_dist: 3.0
 samples_tolerance: 0.006
 samples_tolerance_retries: 3
 
+
 #####################################################################
 # 	Fan Control
 #####################################################################
@@ -349,6 +305,7 @@ heater_temp: 45.0
 #heater_temp: 60
 #fan_speed: 1.0
 
+
 #####################################################################
 # 	LED Control
 #####################################################################
@@ -361,10 +318,12 @@ heater_temp: 45.0
 #value:1
 #cycle_time: 0.01
 
+
 #####################################################################
 # 	Homing and Gantry Adjustment Routines
 #####################################################################
 
+
 #####################################################################
 #	Enclosure Temp Sensor Section
 #####################################################################
@@ -386,63 +345,27 @@ timeout: 1800
 
 [safe_z_home]
 ##	XY Location of the Z Endstop Switch
-##	Update -10,-10 to the XY coordinates of your endstop pin 
-##	(such as 157,305) after going through Z Endstop Pin
-##	Location Definition step.
 home_xy_position: 208, 305 
 speed:100
 z_hop:10
 
 [quad_gantry_level]
 ##	Use QUAD_GANTRY_LEVEL to level a gantry.
-##	Min & Max gantry corners - measure from nozzle at MIN (0,0) and 
-##	MAX (250, 250), (300,300), or (350,350) depending on your printer size
-##	to respective belt positions
-
-#--------------------------------------------------------------------
-##	Gantry Corners for 250mm Build
-##	Uncomment for 250mm build
-#gantry_corners:
-#	-60,-10
-#	310, 320
-##	Probe points
-#points:
-#	50,25
-#	50,175
-#	200,175
-#	200,25
-	
-##	Gantry Corners for 300mm Build
-##	Uncomment for 300mm build
 gantry_corners:
 	-60,-10
 	360,370
-#	Probe points
 points:
 	50,25
 	50,225
 	250,225
 	250,25
-
-##	Gantry Corners for 350mm Build
-##	Uncomment for 350mm build
-#gantry_corners:
-#	-60,-10
-#	410,420
-##	Probe points
-#points:
-#	50,25
-#	50,275
-#	300,275
-#	300,25
-
-#--------------------------------------------------------------------
 speed: 100
 horizontal_move_z: 10
 retries: 5
 retry_tolerance: 0.0075
 max_adjust: 10
 
+
 ########################################
 # EXP1 / EXP2 (display) pins
 ########################################
@@ -463,28 +386,11 @@ aliases:
     EXP2_7=PC15, EXP2_8=<RST>,
     EXP2_9=<GND>, EXP2_10=<5V>
 
+
 #####################################################################
 # 	Displays
 #####################################################################
 
-## 	Uncomment the display that you have
-#--------------------------------------------------------------------
-
-#[display]
-##	RepRapDiscount 128x64 Full Graphic Smart Controller
-#lcd_type: st7920
-#cs_pin: EXP1_4
-#sclk_pin: EXP1_5
-#sid_pin: EXP1_3
-#menu_timeout: 40
-#encoder_pins: ^EXP2_5, ^EXP2_3
-#click_pin: ^!EXP1_2
-
-#[output_pin beeper]
-#pin: EXP1_1
-
-#--------------------------------------------------------------------
-
 [display]
 #	mini12864 LCD Display
 lcd_type: uc1701
@@ -516,8 +422,6 @@ gcode:
         SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
         SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 
 
-#--------------------------------------------------------------------
-
 
 #####################################################################
 # 	Macros
@@ -529,18 +433,9 @@ gcode:
     G28
     QUAD_GANTRY_LEVEL
     G28
-    ##	Uncomment for for your size printer:
-    #--------------------------------------------------------------------
-    ##	Uncomment for 250mm build
-    #G0 X125 Y125 Z30 F3600
-    
-    ##	Uncomment for 300 build
     G0 X150 Y150 Z30 F3600
-    
-    ##	Uncomment for 350mm build
-    #G0 X175 Y175 Z30 F3600
-    #--------------------------------------------------------------------
    
+
 [gcode_macro PRINT_START]
 #   Use PRINT_START for the slicer starting script - please customise for your slicer of choice
 gcode:
@@ -562,15 +457,7 @@ gcode:
     G90                            ; absolute positioning
     G0  X125 Y250 F3600            ; park nozzle at rear
     BED_MESH_CLEAR
-    
+
-## 	Thermistor Types
-##   "EPCOS 100K B57560G104F"
-##   "ATC Semitec 104GT-2"
-##   "NTC 100K beta 3950"
-##   "Honeywell 100K 135-104LAG-J01"
-##   "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
-##   "AD595"
-##   "PT100 INA826"
 
 #*# <---------------------- SAVE_CONFIG ---------------------->
 #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.