konni/klipper_config
1
0
Fork 0
Code Pull requests Releases Activity

v2.4: reformat file

Browse source
This commit is contained in:
Konstantin Koslowski 2021-09-23 10:48:50 +02:00
parent f3e2e9bc3d
commit 4b5981cbe3
1 changed files with 105 additions and 105 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

204
printer.cfg
View file

@ -10,21 +10,21 @@
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config ## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
## *** THINGS TO CHANGE/CHECK: *** ## *** THINGS TO CHANGE/CHECK: ***
## MCU paths [mcu] section ## MCU paths [mcu] section
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file ## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
## Z Endstop Switch location [safe_z_home] section ## Z Endstop Switch location [safe_z_home] section
## Homing end position [gcode_macro G32] section ## Homing end position [gcode_macro G32] section
## Z Endstop Switch offset for Z0 [stepper_z] section ## Z Endstop Switch offset for Z0 [stepper_z] section
## Probe points [quad_gantry_level] section ## Probe points [quad_gantry_level] section
## Min & Max gantry corner postions [quad_gantry_level] section ## Min & Max gantry corner postions [quad_gantry_level] section
## PID tune [extruder] and [heater_bed] sections ## PID tune [extruder] and [heater_bed] sections
## Fine tune E steps [extruder] section ## Fine tune E steps [extruder] section
[mcu] [mcu]
## [X in MOTOR0] - B Motor ## [X in MOTOR0] - B Motor
## [Y in MOTOR1] - A Motor ## [Y in MOTOR1] - A Motor
## [E in MOTOR6] - Extruder ## [E in MOTOR6] - Extruder
## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify ## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
##-------------------------------------------------------------------- ##--------------------------------------------------------------------
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_1E0030000E5053424E363620-if00 serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_1E0030000E5053424E363620-if00
#restart_method: command #restart_method: command
@ -33,28 +33,29 @@ serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_1E0030000E5053424E363620-if00
[printer] [printer]
kinematics: corexy kinematics: corexy
max_velocity: 300 max_velocity: 300
max_accel: 3000 #Max 4000 max_accel: 3000 # Max 4000
max_z_velocity: 25 #Max 15 for 12V TMC Drivers, can increase for 24V max_accel_to_decel: 1500 # default half of max_accel
max_z_velocity: 25 # Max 15 for 12V TMC Drivers, can increase for 24V
max_z_accel: 350 max_z_accel: 350
square_corner_velocity: 5.0 square_corner_velocity: 5.0
##################################################################### #####################################################################
# fluidd # fluidd
##################################################################### #####################################################################
[include fluidd.cfg] [include fluidd.cfg]
##################################################################### #####################################################################
# Macros # Macros
##################################################################### #####################################################################
[include macros.cfg] [include macros.cfg]
##################################################################### #####################################################################
# X/Y Stepper Settings # X/Y Stepper Settings
##################################################################### #####################################################################
## X Stepper on MOTOR0(B Motor) ## X Stepper on MOTOR0(B Motor)
@ -64,12 +65,12 @@ dir_pin: !PF12
enable_pin: !PF14 enable_pin: !PF14
rotation_distance: 40 rotation_distance: 40
microsteps: 16 microsteps: 16
full_steps_per_rotation: 400 # 200: 1.8 deg stepper, 400: 0.9 deg stepper full_steps_per_rotation: 400 # 1.8 deg stepper: 200, 0.9 deg stepper
endstop_pin: PG6 endstop_pin: PG6
position_min: 0 position_min: 0
position_endstop: 300 position_endstop: 300
position_max: 300 position_max: 300
homing_speed: 25 #Max 100 homing_speed: 25 # Max 100
homing_retract_dist: 5 homing_retract_dist: 5
homing_positive_dir: true homing_positive_dir: true
@ -107,7 +108,7 @@ stealthchop_threshold: 0
##################################################################### #####################################################################
# Z Stepper Settings # Z Stepper Settings
##################################################################### #####################################################################
## Z0 Stepper - Front Left on MOTOR2_1 ## Z0 Stepper - Front Left on MOTOR2_1
@ -119,10 +120,10 @@ rotation_distance: 40
gear_ratio: 80:16 gear_ratio: 80:16
microsteps: 16 microsteps: 16
endstop_pin: PG10 endstop_pin: PG10
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) ## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
## (+) value = endstop above Z0, (-) value = endstop below ## (+) value = endstop above Z0, (-) value = endstop below
## Increasing position_endstop brings nozzle closer to the bed ## Increasing position_endstop brings nozzle closer to the bed
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config ## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
#position_endstop: -0.5 #position_endstop: -0.5
position_max: 290 position_max: 290
position_min: -5 position_min: -5
@ -138,7 +139,7 @@ hold_current: 0.8
sense_resistor: 0.110 sense_resistor: 0.110
stealthchop_threshold: 0 stealthchop_threshold: 0
## Z1 Stepper - Rear Left on MOTOR3 ## Z1 Stepper - Rear Left on MOTOR3
[stepper_z1] [stepper_z1]
step_pin: PG4 step_pin: PG4
dir_pin: !PC1 dir_pin: !PC1
@ -155,7 +156,7 @@ hold_current: 0.8
sense_resistor: 0.110 sense_resistor: 0.110
stealthchop_threshold: 0 stealthchop_threshold: 0
## Z2 Stepper - Rear Right on MOTOR4 ## Z2 Stepper - Rear Right on MOTOR4
[stepper_z2] [stepper_z2]
step_pin: PF9 step_pin: PF9
dir_pin: PF10 dir_pin: PF10
@ -172,7 +173,7 @@ hold_current: 0.80
sense_resistor: 0.110 sense_resistor: 0.110
stealthchop_threshold: 0 stealthchop_threshold: 0
## Z3 Stepper - Front Right on MOTOR5 ## Z3 Stepper - Front Right on MOTOR5
[stepper_z3] [stepper_z3]
step_pin: PC13 step_pin: PC13
dir_pin: !PF0 dir_pin: !PF0
@ -191,29 +192,29 @@ stealthchop_threshold: 0
##################################################################### #####################################################################
# Extruder # Extruder
##################################################################### #####################################################################
# E0 on MOTOR6 # E0 on MOTOR6
[extruder] [extruder]
step_pin: PE2 step_pin: PE2
dir_pin: !PE3 dir_pin: !PE3
enable_pin: !PD4 enable_pin: !PD4
## Update value below when you perform extruder calibration ## Update value below when you perform extruder calibration
## If you ask for 100mm of filament, but in reality it is 98mm: ## If you ask for 100mm of filament, but in reality it is 98mm:
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100 ## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
## 22.6789511 is a good starting point ## 22.6789511 is a good starting point
rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears
## Update Gear Ratio depending on your Extruder Type ## Update Gear Ratio depending on your Extruder Type
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio) ## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
## Use 80:20 for M4, M3.1 ## Use 80:20 for M4, M3.1
gear_ratio: 50:17 #BMG Gear Ratio gear_ratio: 50:17 # BMG Gear Ratio
microsteps: 16 microsteps: 16
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree full_steps_per_rotation: 200 # 1.8 deg stepper: 200, 0.9 deg stepper
nozzle_diameter: 0.400 nozzle_diameter: 0.400
filament_diameter: 1.75 filament_diameter: 1.75
heater_pin: PA2 heater_pin: PA2
## Validate the following thermistor type to make sure it is correct ## Validate the following thermistor type to make sure it is correct
sensor_type: ATC Semitec 104GT-2 sensor_type: ATC Semitec 104GT-2
sensor_pin: PF4 sensor_pin: PF4
min_temp: 10 min_temp: 10
@ -224,12 +225,12 @@ min_extrude_temp: 170
#pid_kp = 26.213 #pid_kp = 26.213
#pid_ki = 1.304 #pid_ki = 1.304
#pid_kd = 131.721 #pid_kd = 131.721
## Try to keep pressure_advance below 1.0 ## Try to keep pressure_advance below 1.0
pressure_advance: 0.05 pressure_advance: 0.05
## Default is 0.040, leave stock ## Default is 0.040, leave stock
pressure_advance_smooth_time: 0.040 pressure_advance_smooth_time: 0.040
## E0 on MOTOR6 ## E0 on MOTOR6
[tmc2209 extruder] [tmc2209 extruder]
uart_pin: PE1 uart_pin: PE1
interpolate: false interpolate: false
@ -240,16 +241,16 @@ stealthchop_threshold: 0
##################################################################### #####################################################################
# Bed Heater # Bed Heater
##################################################################### #####################################################################
[heater_bed] [heater_bed]
## SSR Pin - BED_OUT ## SSR Pin - BED_OUT
heater_pin: PA1 heater_pin: PA1
sensor_type: NTC 100K beta 3950 sensor_type: NTC 100K beta 3950
sensor_pin: PF3 sensor_pin: PF3
## Adjust Max Power so your heater doesn't warp your bed ## Adjust Max Power so your heater doesn't warp your bed
max_power: 0.8 # 0.4W per cm2, 360W for 300 build max_power: 0.8 # 0.4W per cm2, 360W for 300 build
min_temp: 0 min_temp: 0
max_temp: 120 max_temp: 120
#control: pid #control: pid
@ -259,12 +260,12 @@ max_temp: 120
##################################################################### #####################################################################
# Probe # Probe
##################################################################### #####################################################################
[probe] [probe]
## Inductive Probe ## Inductive Probe
## This probe is not used for Z height, only Quad Gantry Leveling ## This probe is not used for Z height, only Quad Gantry Leveling
pin: ~PB7 pin: ~PB7
x_offset: 0 x_offset: 0
y_offset: 25.0 y_offset: 25.0
@ -278,37 +279,37 @@ samples_tolerance_retries: 3
##################################################################### #####################################################################
# Fan Control # Fan Control
##################################################################### #####################################################################
[fan] [fan]
## Print Cooling Fan - CNC_FAN0 ## Print Cooling Fan - CNC_FAN0
pin: PA8 pin: PA8
kick_start_time: 0.5 kick_start_time: 0.5
## Depending on your fan, you may need to increase this value ## Depending on your fan, you may need to increase this value
## if your fan will not start. Can change cycle_time (increase) ## if your fan will not start. Can change cycle_time (increase)
## if your fan is not able to slow down effectively ## if your fan is not able to slow down effectively
off_below: 0.10 off_below: 0.10
[heater_fan hotend_fan] [heater_fan hotend_fan]
## Hotend Fan - CNC_FAN1 ## Hotend Fan - CNC_FAN1
pin: PE5 pin: PE5
max_power: 1.0 max_power: 1.0
kick_start_time: 0.5 kick_start_time: 0.5
heater: extruder heater: extruder
heater_temp: 50.0 heater_temp: 50.0
## If you are experiencing back flow, you can reduce fan_speed ## If you are experiencing back flow, you can reduce fan_speed
#fan_speed: 1.0 #fan_speed: 1.0
[heater_fan controller_fan] [heater_fan controller_fan]
## Controller fan - CNC_FAN2 ## Controller fan - CNC_FAN2
pin: PD12 pin: PD12
kick_start_time: 0.5 kick_start_time: 0.5
heater: heater_bed heater: heater_bed
heater_temp: 45.0 heater_temp: 45.0
#[heater_fan exhaust_fan] #[heater_fan exhaust_fan]
## Exhaust fan - CNC_FAN3 ## Exhaust fan - CNC_FAN3
#pin: PD13 #pin: PD13
#max_power: 1.0 #max_power: 1.0
#shutdown_speed: 0.0 #shutdown_speed: 0.0
@ -319,7 +320,7 @@ heater_temp: 45.0
##################################################################### #####################################################################
# LED Control # LED Control
##################################################################### #####################################################################
#[output_pin caselight] #[output_pin caselight]
@ -332,12 +333,12 @@ heater_temp: 45.0
##################################################################### #####################################################################
# Homing and Gantry Adjustment Routines # Homing and Gantry Adjustment Routines
##################################################################### #####################################################################
##################################################################### #####################################################################
# Enclosure Temp Sensor Section # Enclosure Temp Sensor Section
##################################################################### #####################################################################
[thermistor chamber_temp] [thermistor chamber_temp]
temperature1: 25 temperature1: 25
@ -356,7 +357,7 @@ gcode_id: C
timeout: 1800 timeout: 1800
[safe_z_home] [safe_z_home]
## XY Location of the Z Endstop Switch ## XY Location of the Z Endstop Switch
home_xy_position: 208, 305 home_xy_position: 208, 305
speed:100 speed:100
z_hop:10 z_hop:10
@ -373,15 +374,15 @@ algorithm: bicubic
relative_reference_index: 12 relative_reference_index: 12
[quad_gantry_level] [quad_gantry_level]
## Use QUAD_GANTRY_LEVEL to level a gantry. ## Use QUAD_GANTRY_LEVEL to level a gantry.
gantry_corners: gantry_corners:
-60,-10 -60,-10
360,370 360,370
points: points:
50,25 50,25
50,225 50,225
250,225 250,225
250,25 250,25
speed: 100 speed: 100
horizontal_move_z: 10 horizontal_move_z: 10
retries: 5 retries: 5
@ -395,27 +396,27 @@ max_adjust: 10
[board_pins] [board_pins]
aliases: aliases:
# EXP1 header # EXP1 header
EXP1_1=PE8, EXP1_2=PE7, EXP1_1=PE8, EXP1_2=PE7,
EXP1_3=PE9, EXP1_4=PE10, EXP1_3=PE9, EXP1_4=PE10,
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
EXP1_7=PE14, EXP1_8=PE15, EXP1_7=PE14, EXP1_8=PE15,
EXP1_9=<GND>, EXP1_10=<5V>, EXP1_9=<GND>, EXP1_10=<5V>,
# EXP2 header # EXP2 header
EXP2_1=PA6, EXP2_2=PA5, EXP2_1=PA6, EXP2_2=PA5,
EXP2_3=PB1, EXP2_4=PA4, EXP2_3=PB1, EXP2_4=PA4,
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
EXP2_7=PC15, EXP2_8=<RST>, EXP2_7=PC15, EXP2_8=<RST>,
EXP2_9=<GND>, EXP2_10=<5V> EXP2_9=<GND>, EXP2_10=<5V>
##################################################################### #####################################################################
# Displays # Displays
##################################################################### #####################################################################
[display] [display]
# mini12864 LCD Display # mini12864 LCD Display
lcd_type: uc1701 lcd_type: uc1701
cs_pin: EXP1_3 cs_pin: EXP1_3
a0_pin: EXP1_4 a0_pin: EXP1_4
@ -428,7 +429,7 @@ spi_software_mosi_pin: EXP2_6
spi_software_sclk_pin: EXP2_2 spi_software_sclk_pin: EXP2_2
[neopixel btt_mini12864] [neopixel btt_mini12864]
# To control Neopixel RGB in mini12864 display # To control Neopixel RGB in mini12864 display
pin: EXP1_6 pin: EXP1_6
chain_count: 3 chain_count: 3
initial_RED: 0.1 initial_RED: 0.1
@ -436,15 +437,14 @@ initial_GREEN: 0.5
initial_BLUE: 0.0 initial_BLUE: 0.0
color_order: RGB color_order: RGB
# Set RGB values on boot up for each Neopixel. # Set RGB values on boot up for each Neopixel.
# Index 1 = display, Index 2 and 3 = Knob # Index 1 = display, Index 2 and 3 = Knob
[delayed_gcode setdisplayneopixel] [delayed_gcode setdisplayneopixel]
initial_duration: 1 initial_duration: 1
gcode: gcode:
SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3
#*# <---------------------- SAVE_CONFIG ----------------------> #*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
@ -464,21 +464,21 @@ gcode:
#*# [bed_mesh default] #*# [bed_mesh default]
#*# version = 1 #*# version = 1
#*# points = #*# points =
#*# 0.382500, 0.377500, 0.370000, 0.357500, 0.337500 #*# 0.085000, 0.102500, 0.075000, 0.080000, 0.060000
#*# 0.340000, 0.330000, 0.305000, 0.305000, 0.295000 #*# 0.057500, 0.062500, 0.020000, 0.032500, 0.035000
#*# 0.342500, 0.342500, 0.325000, 0.305000, 0.270000 #*# 0.027500, 0.035000, 0.000000, 0.000000, -0.007500
#*# 0.335000, 0.350000, 0.327500, 0.322500, 0.307500 #*# 0.020000, 0.032500, -0.005000, 0.017500, 0.020000
#*# 0.382500, 0.407500, 0.392500, 0.382500, 0.355000 #*# 0.072500, 0.085000, 0.045000, 0.057500, 0.057500
#*# tension = 0.2 #*# tension = 0.2
#*# min_x = 25.0 #*# min_x = 40.0
#*# algo = bicubic #*# algo = bicubic
#*# y_count = 5 #*# y_count = 5
#*# mesh_y_pps = 2 #*# mesh_y_pps = 2
#*# min_y = 25.0 #*# min_y = 40.0
#*# x_count = 5 #*# x_count = 5
#*# max_y = 287.0 #*# max_y = 260.0
#*# mesh_x_pps = 2 #*# mesh_x_pps = 2
#*# max_x = 261.0 #*# max_x = 260.0
#*# #*#
#*# [stepper_z] #*# [stepper_z]
#*# position_endstop = 0.542 #*# position_endstop = 0.642