v2.4: reformat file
This commit is contained in:
parent
f3e2e9bc3d
commit
4b5981cbe3
1 changed files with 105 additions and 105 deletions
204
printer.cfg
204
printer.cfg
|
|
@ -10,21 +10,21 @@
|
|||
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
|
||||
|
||||
## *** THINGS TO CHANGE/CHECK: ***
|
||||
## MCU paths [mcu] section
|
||||
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
||||
## Z Endstop Switch location [safe_z_home] section
|
||||
## Homing end position [gcode_macro G32] section
|
||||
## Z Endstop Switch offset for Z0 [stepper_z] section
|
||||
## Probe points [quad_gantry_level] section
|
||||
## Min & Max gantry corner postions [quad_gantry_level] section
|
||||
## PID tune [extruder] and [heater_bed] sections
|
||||
## Fine tune E steps [extruder] section
|
||||
## MCU paths [mcu] section
|
||||
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
||||
## Z Endstop Switch location [safe_z_home] section
|
||||
## Homing end position [gcode_macro G32] section
|
||||
## Z Endstop Switch offset for Z0 [stepper_z] section
|
||||
## Probe points [quad_gantry_level] section
|
||||
## Min & Max gantry corner postions [quad_gantry_level] section
|
||||
## PID tune [extruder] and [heater_bed] sections
|
||||
## Fine tune E steps [extruder] section
|
||||
|
||||
[mcu]
|
||||
## [X in MOTOR0] - B Motor
|
||||
## [Y in MOTOR1] - A Motor
|
||||
## [E in MOTOR6] - Extruder
|
||||
## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
|
||||
## [X in MOTOR0] - B Motor
|
||||
## [Y in MOTOR1] - A Motor
|
||||
## [E in MOTOR6] - Extruder
|
||||
## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
|
||||
##--------------------------------------------------------------------
|
||||
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_1E0030000E5053424E363620-if00
|
||||
#restart_method: command
|
||||
|
|
@ -33,28 +33,29 @@ serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_1E0030000E5053424E363620-if00
|
|||
[printer]
|
||||
kinematics: corexy
|
||||
max_velocity: 300
|
||||
max_accel: 3000 #Max 4000
|
||||
max_z_velocity: 25 #Max 15 for 12V TMC Drivers, can increase for 24V
|
||||
max_accel: 3000 # Max 4000
|
||||
max_accel_to_decel: 1500 # default half of max_accel
|
||||
max_z_velocity: 25 # Max 15 for 12V TMC Drivers, can increase for 24V
|
||||
max_z_accel: 350
|
||||
square_corner_velocity: 5.0
|
||||
|
||||
|
||||
#####################################################################
|
||||
# fluidd
|
||||
# fluidd
|
||||
#####################################################################
|
||||
|
||||
[include fluidd.cfg]
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Macros
|
||||
# Macros
|
||||
#####################################################################
|
||||
|
||||
[include macros.cfg]
|
||||
|
||||
|
||||
#####################################################################
|
||||
# X/Y Stepper Settings
|
||||
# X/Y Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## X Stepper on MOTOR0(B Motor)
|
||||
|
|
@ -64,12 +65,12 @@ dir_pin: !PF12
|
|||
enable_pin: !PF14
|
||||
rotation_distance: 40
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 400 # 200: 1.8 deg stepper, 400: 0.9 deg stepper
|
||||
full_steps_per_rotation: 400 # 1.8 deg stepper: 200, 0.9 deg stepper
|
||||
endstop_pin: PG6
|
||||
position_min: 0
|
||||
position_endstop: 300
|
||||
position_max: 300
|
||||
homing_speed: 25 #Max 100
|
||||
homing_speed: 25 # Max 100
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
|
|
@ -107,7 +108,7 @@ stealthchop_threshold: 0
|
|||
|
||||
|
||||
#####################################################################
|
||||
# Z Stepper Settings
|
||||
# Z Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## Z0 Stepper - Front Left on MOTOR2_1
|
||||
|
|
@ -119,10 +120,10 @@ rotation_distance: 40
|
|||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
endstop_pin: PG10
|
||||
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||
## (+) value = endstop above Z0, (-) value = endstop below
|
||||
## Increasing position_endstop brings nozzle closer to the bed
|
||||
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
||||
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||
## (+) value = endstop above Z0, (-) value = endstop below
|
||||
## Increasing position_endstop brings nozzle closer to the bed
|
||||
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
||||
#position_endstop: -0.5
|
||||
position_max: 290
|
||||
position_min: -5
|
||||
|
|
@ -138,7 +139,7 @@ hold_current: 0.8
|
|||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z1 Stepper - Rear Left on MOTOR3
|
||||
## Z1 Stepper - Rear Left on MOTOR3
|
||||
[stepper_z1]
|
||||
step_pin: PG4
|
||||
dir_pin: !PC1
|
||||
|
|
@ -155,7 +156,7 @@ hold_current: 0.8
|
|||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z2 Stepper - Rear Right on MOTOR4
|
||||
## Z2 Stepper - Rear Right on MOTOR4
|
||||
[stepper_z2]
|
||||
step_pin: PF9
|
||||
dir_pin: PF10
|
||||
|
|
@ -172,7 +173,7 @@ hold_current: 0.80
|
|||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z3 Stepper - Front Right on MOTOR5
|
||||
## Z3 Stepper - Front Right on MOTOR5
|
||||
[stepper_z3]
|
||||
step_pin: PC13
|
||||
dir_pin: !PF0
|
||||
|
|
@ -191,29 +192,29 @@ stealthchop_threshold: 0
|
|||
|
||||
|
||||
#####################################################################
|
||||
# Extruder
|
||||
# Extruder
|
||||
#####################################################################
|
||||
|
||||
# E0 on MOTOR6
|
||||
# E0 on MOTOR6
|
||||
[extruder]
|
||||
step_pin: PE2
|
||||
dir_pin: !PE3
|
||||
enable_pin: !PD4
|
||||
## Update value below when you perform extruder calibration
|
||||
## If you ask for 100mm of filament, but in reality it is 98mm:
|
||||
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
||||
## 22.6789511 is a good starting point
|
||||
rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears
|
||||
## Update Gear Ratio depending on your Extruder Type
|
||||
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
|
||||
## Use 80:20 for M4, M3.1
|
||||
gear_ratio: 50:17 #BMG Gear Ratio
|
||||
## Update value below when you perform extruder calibration
|
||||
## If you ask for 100mm of filament, but in reality it is 98mm:
|
||||
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
||||
## 22.6789511 is a good starting point
|
||||
rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears
|
||||
## Update Gear Ratio depending on your Extruder Type
|
||||
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
|
||||
## Use 80:20 for M4, M3.1
|
||||
gear_ratio: 50:17 # BMG Gear Ratio
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
||||
full_steps_per_rotation: 200 # 1.8 deg stepper: 200, 0.9 deg stepper
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.75
|
||||
heater_pin: PA2
|
||||
## Validate the following thermistor type to make sure it is correct
|
||||
## Validate the following thermistor type to make sure it is correct
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: PF4
|
||||
min_temp: 10
|
||||
|
|
@ -224,12 +225,12 @@ min_extrude_temp: 170
|
|||
#pid_kp = 26.213
|
||||
#pid_ki = 1.304
|
||||
#pid_kd = 131.721
|
||||
## Try to keep pressure_advance below 1.0
|
||||
## Try to keep pressure_advance below 1.0
|
||||
pressure_advance: 0.05
|
||||
## Default is 0.040, leave stock
|
||||
## Default is 0.040, leave stock
|
||||
pressure_advance_smooth_time: 0.040
|
||||
|
||||
## E0 on MOTOR6
|
||||
## E0 on MOTOR6
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PE1
|
||||
interpolate: false
|
||||
|
|
@ -240,16 +241,16 @@ stealthchop_threshold: 0
|
|||
|
||||
|
||||
#####################################################################
|
||||
# Bed Heater
|
||||
# Bed Heater
|
||||
#####################################################################
|
||||
|
||||
[heater_bed]
|
||||
## SSR Pin - BED_OUT
|
||||
## SSR Pin - BED_OUT
|
||||
heater_pin: PA1
|
||||
sensor_type: NTC 100K beta 3950
|
||||
sensor_pin: PF3
|
||||
## Adjust Max Power so your heater doesn't warp your bed
|
||||
max_power: 0.8 # 0.4W per cm2, 360W for 300 build
|
||||
## Adjust Max Power so your heater doesn't warp your bed
|
||||
max_power: 0.8 # 0.4W per cm2, 360W for 300 build
|
||||
min_temp: 0
|
||||
max_temp: 120
|
||||
#control: pid
|
||||
|
|
@ -259,12 +260,12 @@ max_temp: 120
|
|||
|
||||
|
||||
#####################################################################
|
||||
# Probe
|
||||
# Probe
|
||||
#####################################################################
|
||||
|
||||
[probe]
|
||||
## Inductive Probe
|
||||
## This probe is not used for Z height, only Quad Gantry Leveling
|
||||
## Inductive Probe
|
||||
## This probe is not used for Z height, only Quad Gantry Leveling
|
||||
pin: ~PB7
|
||||
x_offset: 0
|
||||
y_offset: 25.0
|
||||
|
|
@ -278,37 +279,37 @@ samples_tolerance_retries: 3
|
|||
|
||||
|
||||
#####################################################################
|
||||
# Fan Control
|
||||
# Fan Control
|
||||
#####################################################################
|
||||
|
||||
[fan]
|
||||
## Print Cooling Fan - CNC_FAN0
|
||||
## Print Cooling Fan - CNC_FAN0
|
||||
pin: PA8
|
||||
kick_start_time: 0.5
|
||||
## Depending on your fan, you may need to increase this value
|
||||
## if your fan will not start. Can change cycle_time (increase)
|
||||
## if your fan is not able to slow down effectively
|
||||
## Depending on your fan, you may need to increase this value
|
||||
## if your fan will not start. Can change cycle_time (increase)
|
||||
## if your fan is not able to slow down effectively
|
||||
off_below: 0.10
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
## Hotend Fan - CNC_FAN1
|
||||
## Hotend Fan - CNC_FAN1
|
||||
pin: PE5
|
||||
max_power: 1.0
|
||||
kick_start_time: 0.5
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
## If you are experiencing back flow, you can reduce fan_speed
|
||||
## If you are experiencing back flow, you can reduce fan_speed
|
||||
#fan_speed: 1.0
|
||||
|
||||
[heater_fan controller_fan]
|
||||
## Controller fan - CNC_FAN2
|
||||
## Controller fan - CNC_FAN2
|
||||
pin: PD12
|
||||
kick_start_time: 0.5
|
||||
heater: heater_bed
|
||||
heater_temp: 45.0
|
||||
|
||||
#[heater_fan exhaust_fan]
|
||||
## Exhaust fan - CNC_FAN3
|
||||
## Exhaust fan - CNC_FAN3
|
||||
#pin: PD13
|
||||
#max_power: 1.0
|
||||
#shutdown_speed: 0.0
|
||||
|
|
@ -319,7 +320,7 @@ heater_temp: 45.0
|
|||
|
||||
|
||||
#####################################################################
|
||||
# LED Control
|
||||
# LED Control
|
||||
#####################################################################
|
||||
|
||||
#[output_pin caselight]
|
||||
|
|
@ -332,12 +333,12 @@ heater_temp: 45.0
|
|||
|
||||
|
||||
#####################################################################
|
||||
# Homing and Gantry Adjustment Routines
|
||||
# Homing and Gantry Adjustment Routines
|
||||
#####################################################################
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Enclosure Temp Sensor Section
|
||||
# Enclosure Temp Sensor Section
|
||||
#####################################################################
|
||||
[thermistor chamber_temp]
|
||||
temperature1: 25
|
||||
|
|
@ -356,7 +357,7 @@ gcode_id: C
|
|||
timeout: 1800
|
||||
|
||||
[safe_z_home]
|
||||
## XY Location of the Z Endstop Switch
|
||||
## XY Location of the Z Endstop Switch
|
||||
home_xy_position: 208, 305
|
||||
speed:100
|
||||
z_hop:10
|
||||
|
|
@ -373,15 +374,15 @@ algorithm: bicubic
|
|||
relative_reference_index: 12
|
||||
|
||||
[quad_gantry_level]
|
||||
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||
gantry_corners:
|
||||
-60,-10
|
||||
360,370
|
||||
-60,-10
|
||||
360,370
|
||||
points:
|
||||
50,25
|
||||
50,225
|
||||
250,225
|
||||
250,25
|
||||
50,25
|
||||
50,225
|
||||
250,225
|
||||
250,25
|
||||
speed: 100
|
||||
horizontal_move_z: 10
|
||||
retries: 5
|
||||
|
|
@ -395,27 +396,27 @@ max_adjust: 10
|
|||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PE8, EXP1_2=PE7,
|
||||
EXP1_3=PE9, EXP1_4=PE10,
|
||||
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
|
||||
EXP1_7=PE14, EXP1_8=PE15,
|
||||
EXP1_9=<GND>, EXP1_10=<5V>,
|
||||
# EXP1 header
|
||||
EXP1_1=PE8, EXP1_2=PE7,
|
||||
EXP1_3=PE9, EXP1_4=PE10,
|
||||
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
|
||||
EXP1_7=PE14, EXP1_8=PE15,
|
||||
EXP1_9=<GND>, EXP1_10=<5V>,
|
||||
|
||||
# EXP2 header
|
||||
EXP2_1=PA6, EXP2_2=PA5,
|
||||
EXP2_3=PB1, EXP2_4=PA4,
|
||||
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
|
||||
EXP2_7=PC15, EXP2_8=<RST>,
|
||||
EXP2_9=<GND>, EXP2_10=<5V>
|
||||
# EXP2 header
|
||||
EXP2_1=PA6, EXP2_2=PA5,
|
||||
EXP2_3=PB1, EXP2_4=PA4,
|
||||
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
|
||||
EXP2_7=PC15, EXP2_8=<RST>,
|
||||
EXP2_9=<GND>, EXP2_10=<5V>
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Displays
|
||||
# Displays
|
||||
#####################################################################
|
||||
|
||||
[display]
|
||||
# mini12864 LCD Display
|
||||
# mini12864 LCD Display
|
||||
lcd_type: uc1701
|
||||
cs_pin: EXP1_3
|
||||
a0_pin: EXP1_4
|
||||
|
|
@ -428,7 +429,7 @@ spi_software_mosi_pin: EXP2_6
|
|||
spi_software_sclk_pin: EXP2_2
|
||||
|
||||
[neopixel btt_mini12864]
|
||||
# To control Neopixel RGB in mini12864 display
|
||||
# To control Neopixel RGB in mini12864 display
|
||||
pin: EXP1_6
|
||||
chain_count: 3
|
||||
initial_RED: 0.1
|
||||
|
|
@ -436,15 +437,14 @@ initial_GREEN: 0.5
|
|||
initial_BLUE: 0.0
|
||||
color_order: RGB
|
||||
|
||||
# Set RGB values on boot up for each Neopixel.
|
||||
# Index 1 = display, Index 2 and 3 = Knob
|
||||
# Set RGB values on boot up for each Neopixel.
|
||||
# Index 1 = display, Index 2 and 3 = Knob
|
||||
[delayed_gcode setdisplayneopixel]
|
||||
initial_duration: 1
|
||||
gcode:
|
||||
SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
|
||||
SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
|
||||
SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3
|
||||
|
||||
SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
|
||||
SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
|
||||
SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
|
|
@ -464,21 +464,21 @@ gcode:
|
|||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.382500, 0.377500, 0.370000, 0.357500, 0.337500
|
||||
#*# 0.340000, 0.330000, 0.305000, 0.305000, 0.295000
|
||||
#*# 0.342500, 0.342500, 0.325000, 0.305000, 0.270000
|
||||
#*# 0.335000, 0.350000, 0.327500, 0.322500, 0.307500
|
||||
#*# 0.382500, 0.407500, 0.392500, 0.382500, 0.355000
|
||||
#*# 0.085000, 0.102500, 0.075000, 0.080000, 0.060000
|
||||
#*# 0.057500, 0.062500, 0.020000, 0.032500, 0.035000
|
||||
#*# 0.027500, 0.035000, 0.000000, 0.000000, -0.007500
|
||||
#*# 0.020000, 0.032500, -0.005000, 0.017500, 0.020000
|
||||
#*# 0.072500, 0.085000, 0.045000, 0.057500, 0.057500
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 25.0
|
||||
#*# min_x = 40.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 25.0
|
||||
#*# min_y = 40.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 287.0
|
||||
#*# max_y = 260.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 261.0
|
||||
#*# max_x = 260.0
|
||||
#*#
|
||||
#*# [stepper_z]
|
||||
#*# position_endstop = 0.542
|
||||
#*# position_endstop = 0.642
|
||||
|
|
|
|||
Loading…
Reference in a new issue