127 lines
5.7 KiB
INI
127 lines
5.7 KiB
INI
#####################################################################
|
|
# Z Calibration
|
|
#####################################################################
|
|
[z_calibration]
|
|
# The X and Y coordinates (in mm) for clicking the nozzle on the
|
|
# Z endstop.
|
|
probe_nozzle_x: 208
|
|
probe_nozzle_y: 305
|
|
# The X and Y coordinates (in mm) for clicking the probe's switch
|
|
# on the Z endstop.
|
|
probe_switch_x: 201
|
|
probe_switch_y: 284
|
|
# The X and Y coordinates (in mm) for probing on the print surface
|
|
# (e.g. the center point) These coordinates will be adapted by the
|
|
# probe's X and Y offsets. The default is the relative_reference_index
|
|
# of the configured bed_mesh. It will raise an error if there is no
|
|
# probe_bed site and no bed_mesh with a relative_reference_index
|
|
# configured.
|
|
probe_bed_x: 150
|
|
probe_bed_y: 150
|
|
# The trigger point offset of the used mag-probe switch.
|
|
# This needs to be fined out manually. More on this later
|
|
# in this section..
|
|
switch_offset: 0.42
|
|
# The maximum allowed deviation of the calculated offset.
|
|
# If the offset exceeds this value, it will stop!
|
|
# The default is 1.0 mm.
|
|
max_deviation: 1.5
|
|
# The number of times to probe each point. The probed z-values
|
|
# will be averaged. The default is from the probe's configuration.
|
|
#samples: default from "probe:samples" section
|
|
# The maximum Z distance (in mm) that a sample may differ from other
|
|
# samples. The default is from the probe's configuration.
|
|
#samples_tolerance: default from "probe:samples_tolerance" section
|
|
# The number of times to retry if a sample is found that exceeds
|
|
# samples_tolerance. The default is from the probe's configuration.
|
|
#samples_tolerance_retries: default from "probe:samples_tolerance_retries" section
|
|
# The calculation method when sampling more than once - either
|
|
# "median" or "average". The default is from the probe's configuration.
|
|
#samples_result: default from "probe:samples_result" section
|
|
# The distance in mm to move up before moving to the next
|
|
# position. The default is two times the z_offset from the probe's
|
|
# configuration.
|
|
clearance: 7.5
|
|
#position_min: default from "stepper_z:position_min" section.
|
|
# The moving speed in X and Y. The default is 50 mm/s.
|
|
speed: 200
|
|
# Speed (in mm/s) of the Z axis when lifting the probe between
|
|
# samples and clearance moves. The default is from the probe's
|
|
# configuration.
|
|
#lift_speed: default from "probe:lift_speed" section
|
|
# The fast probing speed (in mm/s) used, when probing_first_fast
|
|
# is activated. The default is from the Z rail configuration.
|
|
#probing_speed: default from "stepper_z:homing_speed" section.
|
|
# The slower speed (in mm/s) for probing the recorded samples.
|
|
# The default is second_homing_speed of the Z rail configuration.
|
|
#probing_second_speed: default from "stepper_z:second_homing_speed" section.
|
|
# Distance to back off (in mm) before probing the next sample.
|
|
# The default is homing_retract_dist from the Z rail configuration.
|
|
#probing_retract_dist: default from "stepper_z:homing_retract_dist" section.
|
|
# If true, the first probing is done faster by the probing speed.
|
|
# This is to get faster down and the result is not recorded as a
|
|
# probing sample. The default is false.
|
|
probing_first_fast: true
|
|
# If true, the first probing is done faster by the probing speed.
|
|
# This is to get faster down and the result is not recorded as a
|
|
# probing sample. The default is false.
|
|
start_gcode: DETACH_PROBE
|
|
# A list of G-Code commands to execute prior to each calibration command.
|
|
# See docs/Command_Templates.md for G-Code format. This can be used to
|
|
# attach the probe.
|
|
before_switch_gcode: ATTACH_PROBE
|
|
# A list of G-Code commands to execute prior to each probing on the
|
|
# mag-probe. See docs/Command_Templates.md for G-Code format. This can be
|
|
# used to attach the probe after probing on the nozzle and before probing
|
|
# on the mag-probe.
|
|
end_gcode: DETACH_PROBE
|
|
# A list of G-Code commands to execute after each calibration command.
|
|
# See docs/Command_Templates.md for G-Code format. This can be used to
|
|
# detach the probe afterwards.
|
|
|
|
#####################################################################
|
|
## With these settings, the probe is attached after probing the nozzle
|
|
## and before probing the switch !!
|
|
#####################################################################
|
|
## Otherwise, starting with the probe attached would be like this:
|
|
start_gcode: ATTACH_PROBE
|
|
#before_switch_gcode: ATTACH_PROBE
|
|
end_gcode: DETACH_PROBE
|
|
#####################################################################
|
|
|
|
#####################################################################
|
|
# Macros
|
|
#####################################################################
|
|
|
|
###################################################################
|
|
# !!! Caution !!!
|
|
#
|
|
# This Macro is only needed if not using the start/end_gcode
|
|
# properties to attach/detach the probe
|
|
###################################################################
|
|
[gcode_macro CALIBRATE_Z]
|
|
description: Automatically calibrates the nozzles offset to the print surface and dock/undock MagProbe
|
|
rename_existing: CALIBRATE_Z_BASE
|
|
gcode:
|
|
##### get user defines #####
|
|
{% set z_hop = printer['gcode_macro _USER_VARIABLE'].probe_z_min|float %}
|
|
##### get toolhead parameters #####
|
|
{% set act_z = printer.gcode_move.gcode_position.z|float %}
|
|
#### end of definitions #####
|
|
## reduce current of motors
|
|
_SET_ACC VAL=HOME
|
|
_SET_CURRENT VAL=HOME
|
|
_CG28 RESET_SETTINGS=false
|
|
{% if act_z < z_hop %}
|
|
G90 ; absolute positioning
|
|
{action_respond_info("CALIBRATE_Z: High must be above %.2f" % z_hop)}
|
|
G1 Z{z_hop} F900 ; move head up
|
|
{% endif %}
|
|
#ATTACH_PROBE
|
|
CALIBRATE_Z_BASE
|
|
#DETACH_PROBE
|
|
{% if params.RESET_SETTINGS|default('true') == 'true' %}
|
|
## return to org current settings
|
|
_SET_CURRENT
|
|
_SET_ACC
|
|
{% endif %}
|